Kinze 3140 Stack Fold Planter Rev. 7/14 - Manual (Page 88)

M0245-01 Model 3140
5-8 9/12
TM
KPM III Monitor Operation
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
10.Calibrate Speed Sensor
Logdata
Seed Data Logging
Cancel OK
Destination
File Name
Log files are stored on USB drive in folder KPMIII_DataLogs
Names end with .999.csv (999 is a 3 digit sequence number)
Comment for file:
Temperature
Add new...
32 Humidity 0
Serial Port
A B C
I J K
D
L
Q R S T
Z ( Y )
F
M N
G
O
U V W
/ , .
E H
P
X Space
Clear -
DATA LOggINg MODE
STEP 1 Scroll to ‘‘4. Setup Data Logging” by turning the
rotary encoder knob or using the arrow keys. Press
the knob or Enter key to display the highlighted item.
NOTE: Data logging changes cannot be made while data is
being logged. If the monitor is logging data the following
warning will appear. To stop data logging and continue.
• Press the knob or Enter key to close the warning.
• Then in the “Setup Mode” press the F3 key next to
“StopLog”.
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
Logdata
10.Calibrate Speed Sensor
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
10.Calibrate Speed Sensor
StopLog
Data Logging Warning
Changing data logging parameters is not
allowed while data is being logged.
OK
STEP 3 Use the knob or arrow keys to highlight the “File
Name” box. Press the knob or Enter key and a drop
down list of the files will be displayed. Select “Add
new…” to enter a file name and press the knob or
enter key to display a keyboard.
STEP 4 Select “Add new…” to enter a file name and press
the knob or enter key to display a keyboard.
STEP 5 Add a new file name by using the drop down
keyboard. Spell out the file name by highlighting
each letter and pressing the knob or Enter key.
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
10.Calibrate Speed Sensor
Logdata
Seed Data Logging
Cancel OK
Destination
File Name
Log files are stored on USB drive in folder KPMIII_DataLogs
Names end with .999.csv (999 is a 3 digit sequence number)
Comment for file:
Temperature
Add new...
32 Humidity 0
Serial Port
Serial Port
USB Flash Drive
Serial and UBS
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
10.Calibrate Speed Sensor
Logdata
Seed Data Logging
Cancel OK
Destination
File Name
Log files are stored on USB drive in folder KPMIII_DataLogs
Names end with .999.csv (999 is a 3 digit sequence number)
Comment for file:
Temperature
Add new...
32 Humidity 0
Serial Port
Add new...
Add new...
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
10.Calibrate Speed Sensor
Logdata
Seed Data Logging
Cancel OK
Destination
File Name
Log files are stored on USB drive in folder KPMIII_DataLogs
Names end with .999.csv (999 is a 3 digit sequence number)
Comment for file:
Temperature
Add new...
32 Humidity 0
Serial Port
A B C
I J K
D
L
Q R S T
Z ( Y )
F
M N
G
O
U V W
/ , .
E H
P
X Space
Clear -
STEP 2 Turn the knob or use the arrow keys to highlight the
“Destination” box then press the knob or Enter key.
Highlight the desired option either “Serial Port”, “USB
Flash Drive”, or “Serial and USB” and press the knob
or Enter key.
STEP 6 Use knob or arrow keys to scroll to “Comment
for file” box. Press knob or Enter key to display
drop down keyboard. Use keyboard to enter a
Comment for the file then press Enter key.