Setting the communication adaptor board, Communication adaptor (sha-ka128aab), Remote control functions – Sanyo CHX06052 User Manual
Page 134: 1) switch operation overview, 2) adaptor number setting procedure, 4) other settings
2-116
Remote Control Functions
6. Communication Adaptor (SHA-KA128AAB)
Setting the Communication Adaptor board
The switches on the board control the adaptor numbers, turn the indoor/outdoor control wire connection on and off, and control other settings.
(1) Switch operation overview
Item selection
Use the
UP
and
DOWN
keys to find the desired item, then press the
SET
key to select.
Changing the settings
Use the
UP
and
DOWN
keys to change the setting, then press the
SET
key to confirm.
Hold down the
HOME
key for at least two seconds to reset to the default setting
(Any settings in progress will be
lost.)
(2) Adaptor number setting procedure
Hold down the
HOME
key for at least two seconds so the initial display shows as follows:
(no.00)
After 2 seconds
(AdP.dt)
Press the
UP
key five times so the following display appears:
(no.05)
This automatically switches to the below display after 2 more seconds. (Operation is not necessary.)
(FirSt)
Press the
SET
key so the below display appears. (Only the green monitor LED is on.)
(1.Ano.00) (Factory setting)
Hold down the
SET
key for at least 1 second so the “00” part blinks, indicating that the setting can be changed. (The green and red monitor
LEDs are both on.)
Use the
UP
and
DOWN
keys to set the adaptor number.
For example, to set number 3, press the
UP
key three times. The following will display:
(1.Ano.03)
Press the
SET
key for at least 1 second to confirm. (Only the green monitor LED is on.)
4
D8
D3
D4
D5
D6
D7
S6
S9
S8
S7
D1
D2
UP DOWN SET
HOME
7-segment LED
Home key
Monitor LED
D1: red
D2: green
Set key
Down key
Up key
(3) Setting the indoor/outdoor control wire connection on/off
Repeat steps
to
in section (2) “Adaptor number setting procedure” above. The following will display:
(1.Ano.03) (When the adaptor number is 3)
Press the
UP
key once so the following display appears:
(2.Adyu.0) (Factory setting)
Hold down the
SET
key for at least 1 second so the “0” part blinks, indicating that the setting can be changed. (The green and red monitor
LEDs are both on.)
Use the
UP
and
DOWN
keys to turn the indoor/outdoor control wire connection on or off as shown in the table below.
For example, to connect the indoor/outdoor control wire only to LINK1, press the
UP
key once. The following display will result:
(2.AdYu.1)
Press the
SET
key for at least 1 second to confirm. (Only the green monitor LED is on.)
(4) Other settings
With the display status showing as in number
in section (2) “Adaptor number setting procedure”, press the
UP
and
DOWN
keys to select
the setting items shown in the following table on page 2-118. Set as needed.
The setting procedure is the same as above.
(Press the
SET
key for at least 1 second, press the
UP
and
DOWN
keys to change, then press the
SET
key at least one second to confirm.)
Note
When configuring, do not set the same adaptor number more than once.
*
Use numbers between 1 and 7 for connecting to an Intelligent Controller.
Turn the indoor/outdoor control wire connection on/off as appropriate.
(Set to “Off” for LINKs with no connection.)
For connecting the indoor/outdoor control wire to only one link, use the
“LINK1” side.
Setting value
Indoor/outdoor control wire connection
0
LINK1: On, LINK2: On (factory setting)
1
LINK1: On, LINK2: Off
2
LINK1: Off, LINK2: On
3
LINK1: Off, LINK2: Off
MiniECO-i.indb 116
2007/06/20 16:30:26