Panasonic WJ-NT204 - Manual (Page 141)

142
SPECIFICATIONS
General
Power supply: 120 V AC, 60 Hz
Power consumption: 13 W max.
Weight: 4 k g (8.8 lbs.)
Dimensions: 420 mm (W) x 44 mm (H) x 350 mm (D) (no rubber feet and bosses included)
16-9/16” (W) x 1-3/4” (H) x 13-3/4” (D)
Working temperature range: Specified temperature: +5 ˚C ~ +40 ˚C (41 ˚F ~104 ˚F)
Operating temperature: -10 ˚C ~ +60 ˚C (14 ˚F ~140 ˚F)
Working humidity range: 95 % maximum
Applicable line: 10BASE-T/100BASE-TX, RJ45
Communication protocols: TCP, IP, UDP, ICMP, FTP, HTTP, H.323
Video input: Video input 1 - 4 and AUX, NTSC composite / 1 V[p-p]/75
Ω
, BNC
Video output Video output 1 - 4, NTSC composite / 1 V[p-p]/75
Ω
, BNC
Monitor/Spot output, NTSC composite / 1 V[p-p]/75
Ω
, BNC
Image compression system: H.261, maximum communication rate 1 Mbps
(0/16/32/64/128/256/384/512/768/1024 kbps manually)
elements CIF: 352 x 288 / 640x480 (Image Size) max. 30 fps
JPEG, maximum 15 fps, CIF: 352 x 288, VGA: 640 x 480
Audio input Audio input x1, -10 dB 47 k
Ω
, RCA pin jack
Audio output: Audio output x1, –10 dB 300
Ω
, RCA pin jack:
Audio compression system: G.711-µ/G711-A, audio band 3.4kHz, or no sound
Control System
Data port: RS-232C (D-sub 9 pin male)/ 4-wire RS-485 (RJ-11 connector),
baud rate = 4 800 bps/ 9 600/19200 bps,
data length = 7-bit/8-bit,
stop = 1-bit/2-bit, parity = NONE/ODD/EVEN
Note) The rear DIP switch specifies RS-232C or RS-485.
Parallel port: D-Sub 25-pin female, Input x8 (make-contact),
Output x8 (open collector output)
Forced (line) disconnection input x1 (make-contact)
Clock adjust signal input x1 (make-contact)
Mid-communication output x1 (open collector output)
Parallel data strobe output x1 (open collector output), +12 V output (50 mA max.)
Sensor input/Trigger output: D-Sub 25-pin female, sensor input x8 (make-contact)
Trigger output x8 (open collector output)
Host port: RS-232C (D-Sub 9-pin male) or 4-wire RS-485 (RJ-11 connector),
rate = 4 800/9 600/19 200 bps, data length = 8-bit (fixed),
stop = 1-bit (fixed), parity = NONE
Note) The front DIP switch specifies RS-232C or RS-485.
Operation System
Remote control connector: Rear: RJ-11 modular port
Host port, data port RS-485 terminating SW: ON/OFF (Set with dip switches on the rear)
Data port RS485 line changeover SW:
Straight/crossover (The rear DIP switch specifies the wiring.)
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.