GE Industrial Solutions AF-300 G11 - Manual (Page 125)

11-2
Data subject to change without notice 7/07. © 2007 GE Drives
Three-phase 460V series
F50
001
002
003
005
007
010
015
020
025
030
040
050
060
075
100
125
150
200
250
300
350
400
450
500
600
Norminal 460V system applied motor
HP
1/2
1235
7.
5
10
15
20
25
30
40
50
60
75
10
0
12
5
15
0
20
0
25
0
30
0
35
0
40
0
45
0
50
0
60
0
Rated Capacity *1)
kVA 1.1
1.9
2.9
4.3
7.1
10
14
19
23
31
35
47
59
72
89
119
140
167
201
242
300
330
414
466
518
590
Rated Voltage *2)
V
3-phase, 380V , 400V , 415V /50Hz , 380V , 400V , 440V , 460V /60Hz
Rated Current *3)
A 1.5
2.5
3.7
5.5
9.0
13
18
24
30
39
45
60
75
91
112
150
176
210
253
304
377
415
520
585
650
740
Overload Capability
150% of rated current for 1min ,
150% of rated current for 1min ,
200% of rated current for 0.5s
180% of rated current for 0.5s
Rated Frequency
Hz
50, 60Hz
Input
Phases, Voltage, Frequency
3-phase, 380 to 480V , 50/60Hz
3-phase, 380 to 440V /50Hz , 380 to 480V /60Hz
ratings
* 380V/50Hz and 380 to 415V/60Hz *4)
Voltage / frequency variations
-Voltage : +10 to -15% ( Voltage unbalance *5) : 2% or less )
-Frequency :+5 to -5%
Momentary voltage dip
When the input voltage is 310V or more, the inverter can be operated continuously.
capability *6)
When the input voltage drops below 310V from rated voltage, the inverter can be operated for 15ms . (less th
an 85% load of nominal applied motors)
The smooth recovery method is selectable.
Output
Maximum Freq.
50 to 400Hz *10)
frequency
Base Freq.
25 to 400Hz *10)
Setting
Starting Freq.
0.1 to 60Hz , Continuous time : 0.0 to 10.0s
Carrier Freq. *8)
0.75 to 15kHz
0.75 to 10kHz
The minimum carrier frequency changes depend on maximum output frequency.
Accuracy (Stability)
-Analog setting
: ±0.2% of Maximum frequency (at 25 ±10 degrees C)
-Digital setting
: ±0.01% of Maximum frequency (at -10 to +50 degrees C)
Setting resolution
-Analog setting
: 1/3000 of Max. frequency ex.) 0.02Hz at 60Hz , 0.15Hz at 400Hz
-Digital setting
: 0.01Hz at Maximum frequency of up to 99.99Hz (0.1Hz at Maximum frequency of 100Hz and above)
-Link setting
: Two methods are selectable.
Control
Volt/Freq Characteristic
320 to 480V (with AVR control) at base and maximum frequency, adjustable
Torque boost
Constant toruque load
Variable torque load
Automatic (setting code)
0.0
-
Manual (setting code)
2.0 to 20.0
0.1 to 1.9 *9)
Starting torque
200% (with Dynamic torque vector control selected)
180% (with Dynamic torque vector control selected)
Braking
Braking torque
150%
100%
20% *11)
15 to 10% *11)
Standards
Time
s
5
5
No limit
Duty cycle
%
5353232
N
o
li
m
it
Braking torque
150%
100%
Options
Time
s
45
45
30
20
10
8
10
Duty cycle
%
22
10
7
5
5
5
10
DC injection braking
Starting frequency : 0.1 to 60.0Hz , Braking time : 0.0 to 30.0s, Braking level : 0 to 100% of rated current
Enclosure
NEMA Type1, Type 4
NEMA Type1, Type12
Open, Open with NEMA Type 12 Heatsink, NEMA Type 1
Cooling method
Natural
Fan cooling
Standards
-UL/cUL
NOTES *1) Inverter output capacity [kVA] at
460V.
*2) Output voltage is proportional to the power supply voltage and can't exceed the power supply voltage. *3) Current derating may be required in case of low impedance load such as high frequency motor. *4) Change the tap of auxiliary transformer. 380V/50Hz and 380 to 415V/60Hz : Change over CN UX connector from U1 part to U2 part. (Reference to the Instruction manua
l)
Input voltage
CN UX connector
400 to 440V/50Hz, 440 to 480V/60Hz
U1 (Factory setting)
380V/50Hz (398V or smaller),
380 to 415V/60Hz (430V or smaller)
*5) Reference to the IEC 61800-3( 5.2.3 )
(Maximum voltage[V] - Minimum voltage[V] )
3-phase averaging voltageV
*6) Input power : 85% *8) If carrier frequency is set at more than 10kHz and an overheat condition (detected by internal thermal sensor ) occurs, i
nverter will automatically reduce carrier frequency to 8kHz ,
in order to avoid trip.(Available up to 30HP unit) *9) When setting into 0.1, the starting torque gets 50% *10) Above 120Hz application, please contact the factory *11) With a nominal applied motor.(Average torque when the motor decelerates and stops from 60Hz. It may change according to t
he motor loss.)
-LOW VOLTAGE directive -IEC 61800-2 Rating, specifications for low voltage adjustable frequency a.c. power drive systems)
-EMC directive -IEC 61800-3 (EMC product standard including specific test methods)
1/20000 of Maximum frequency ex.) 0.003Hz at 60Hz , 0.01Hz at 400Hz 0.01Hz (Fixed)
Unbalance in power supply voltage [%] =
X
67 [%]
U2
Type designation ( * * indicate product revision) 6KG1143_ _ _X1 * * (NEMA Type1) 6KG1143_ _ _ X2 * * (NEMA Type12) 6KG1143_ _ _ X4 * * (NEMA Type 4) 6KG1143_ _ _ X8 * * (Open, Type 12 Heatsink) 6KG1143_ _ _ X9 * * (Open)