Set value 0 to 30 hz in 1hz increments (min.) – GE Industrial Solutions AF-300 G11 User Manual
Page 81
5-28
Data subject to change without notice 7/07. © 2007 GE Drives
This function makes the set frequency jump so that the
drive’s output frequency does not match the mechanical
resonance point of the load.
Up to three jump points can be set.
This function is ineffective if jump frequencies 1 to 3 are
set to 0 Hz.
A jump does not occur during acceleration or decelera-
tion.
If a jump frequency setting range overlaps another range,
both ranges are added to determine the actual jump area.
C05-C19 Multi-step frequency 1 to 15
C 0 5
M U L T I
H z – 1
C 0 6
M U L T I
H z – 2
C 0 7
M U L T I
H z – 3
C 0 8
M U L T I
H z – 4
C 0 9
M U L T I
H z – 5
C 1 0
M U L T I
H z – 6
C 1 1
M U L T I
H z – 7
C 1 2
M U L T I
H z – 8
C 1 3
M U L T I
H z – 9
C 1 4
M U L T I
H z 1 0
C 1 5
M U L T I
H z 1 1
C 1 6
M U L T I
H z 1 2
C 1 7
M U L T I
H z 1 3
C 1 8
M U L T I
H z 1 4
C 1 9
M U L T I
H z 1 5
C01 Jump frequency 1
C02 Jump frequency 2
C03 Jump frequency 3
C04 Jump frequency hysteresis
C: Control Functions of Frequency
Jump frequency 3
➝
➝
Jump frequency 2
➝
➝
Output frequency
(Hz)
Jump frequency
width
Jump frequency
width
Jump frequency
width
Jump frequency 1
Set frequency (Hz)
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
Output Frequency
(Hz)
FWD-CM
SS1-CM
SS2-CM
SS4-CM
SS8-CM
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
C05
C13
C12
C11
C10
C09
C08
C07
C06
C14
C15
C16
C17
C18
C19
➝
➝
➝
➝
Jump frequency 2
Jump frequency 1
Set frequency (Hz)
Jump frequency
width
➝
➝
➝
➝
➝
➝
Output frequency
(Hz)
➝
➝
➝
➝
➝
➝
➝
➝
Actual
jump width
Set value 0 to 400 Hz in 1Hz increments (min.)
C 0 4
J U M P
H Y S T R
Set value 0 to 30 Hz in 1Hz increments (min.)
C 0 1
J U M P
H z
1
C 0 2
J U M P
H z
2
C 0 3
J U M P
H z
3
Set value 0 to 400 Hz In 0.01 Hz increments (min.)
Multistep frequencies 1 to 15 can be switched by turning
terminal functions SS1, SS2, SS4, and SS8 on and off.
(See E01 to E09 for terminal function definitions.)
OFF is the default value any undefined SS1, SS2, SS4,
and SS8 terminals.
Related functions: E01 to E09 (Set value: 0 to 3)