Extron Electronics MTPX Plus 6400 Series User Guide - Manual (Page 76)

Command/Response Table for SIS Commands
Symbol Definitions
] = CR/LF (carriage return/line feed) (hex 0D 0A)
} = Carriage return (no line feed, hex 0D)
| = Pipe (can be used interchangeably with the
}
character)
• = Space character
E = Escape key (hex 1B)
X!
= Input number (for tie) 00 – (maximum number of inputs for your matrix size) (00 = untied)
X@ = Output number 01 – (maximum number of outputs for your matrix size)
X#
= TP input number 01 – (maximum number of TP inputs for your matrix size)
X$ = Audio / RS-232 wire pair input type 0 = audio
1 = RS-232
X% = RS-232 output insertion port number 01 – 16
X^ = RS-232 output insert status 0 = disabled
1 = RS-232 enabled
2 = UART enabled
X&
= Input level and peaking range 000 – 255
X* = Threshold 0 = outside of threshold
1 = within threshold
X( = Skew adjustment range 00 – 31 (each step = 2 ns)
X1) = Video plane 0 = red
1 = green
2 = blue
X1! = Input number 01 – (maximum number of inputs for your matrix size)
X1@ = DDC value (EDID) 00 = Automatic 18 = 1366 x 768 @ 60 Hz
01 = Output 1 19 = 1400 x 1050 @ 50 Hz
02 = Output 2 20 = 1400 x 1050 @ 60 Hz
03 = 800 x 600 @ 50 Hz 21 = 1440 x 900 @ 50 Hz
04 = 800 x 600 @ 60 Hz 22 = 1440 x 900 @ 60 Hz
05 = 1024 x 768 @ 50 Hz 23 = 1600 x 1200 @ 50 Hz
06 = 1024 x 768 @ 60 Hz 24 = 1600 x 1200 @ 60 Hz
07 = 1280 x 720 @ 50 Hz 25 = 1680 x 1050 @ 50 Hz
08 = 1280 x 720 @ 60 Hz 26 = 1680 x 1050 @ 60 Hz
09 = 1280 x 768 @ 50 Hz 27 = 1920 x 1080 @ 50 Hz
10 = 1280 x 768 @ 60 Hz 28 = 1920 x 1080 @ 60 Hz
11 = 1280 x 800 @ 50 Hz 29 = 1920 x 1200 @ 50 Hz
12 = 1280 x 800 @ 60 Hz 30 = 1920 x 1200 @ 60 Hz
13 = 1280 x 1024 @ 50 Hz 31 = User defined
14 = 1280 x 1024 @ 60 Hz 32 = User defined
15 = 1360 x 768 @ 50 Hz 33 = User defined
16 = 1360 x 768 @ 60 Hz 34 = User defined
17 = 1366 x 768 @ 50 Hz
X1# = Mute, pre-peaking, Lock mode 0 = off / Mode 0 / not OK or not installed
1 = on / Mode 1 / OK
2 = Mode 2
X1$
= Local video output number 01 – 04
X1% = Local output sync polarity 0 = H– / V– (default)
1 = H+ / V–
2 = H – / V+
3 = H+ / V+
4 = No sync processing (composite, S-video, YUV)
X1^ = TP output number 01 – (maximum number of TP outputs for your model)
X1&
= Local audio output number 01 – 08
X1* = Volume adjustment range 00 – 64 (1 dB per step) (default = 64 [0 dB])
(
see the table on page 75)
X1( = Audio gain 00 – 24 (1 dB per step)
X2) = Numeric dB value –18 to + 24 (45 steps of gain or attenuation (default = 0 dB)
X2! = Audio attenuation 01 – 18 (1 dB per step)
MTPX Plus 6400 Series Matrix Switchers • Programming Guide 70