Extron Electronics MTPX Plus 6400 Series User Guide - Manual (Page 84)

Command/Response Table for SIS Commands (continued)
Command ASCII Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Save, recall, and directly write presets (continued)
Write room outputs EX2$ , X@ 1 , X@ 2 , ... X@ n MR ] See notes.
Mpr X2$ , X@ 1 , X@ 2 , ... X@ n ]
NOTES: • A room can contain a maximum of 16 outputs ( X@ s).
• An output can belong to only one room.
• The maximum number of rooms ( X2$ s) is 10.
Example: E 8,3,Ø4,5,6MR } Mpr8,Ш3,Ш4,Ш5,Ш6 ] Outputs 3, 4, 5, and 6 are assigned to room 8.
Read room outputs EX2$ MR } X2$ , X@ 1 , X@ 2 , ... X@ n ]
NOTE: If no outputs have been assigned to the room, the switcher returns [unassigned] ] .
Example: E 3MR } Room•#Ш3••••,Ш1,Ш2,Ш8,Ш9 ]
Outputs 1, 2, 8, and 9 are assigned to room 3.
Save current ties as a room
preset X2$ * X2@ , Rmm X2$ •Spr X2@] Command character is a comma.
NOTE: You must have assigned outputs to a room ( EX2$ ,MR } ) before you can save a room preset.
Example: 3*9, RmmØ3•SprØ9 ] Save current ties as preset 9 for room 3.
Recall room preset X2$ * X2@ . Rmm X2$ •Rpr X2@] Command character is a period.
Read room outputs EX2$ MR } X2# , X@ 1 , X@ 2 , ... X@ n ]
NOTE: The default name ( X2# ) is the room number with four trailing spaces: “Room•# X2$ ••••.”
Example: E 3MR } Room•#Ш3••••,Ш1,Ш2,Ш8,Ш9 ]
Outputs 1, 2, 8, and 9 are assigned to room 3.
Clear room preset ties E + X2$ * X2@ PØ*! ] Rmm X2$ •Spr X2@] Clear all ties in room X2$ preset X2@ .
Directly write a room preset E + X2$ * X2@ P X! * X@ ! X! * X@ % X! * X@ $ ... X! * X@ ! } Enter as many ties as are valid for this
configuration. The ! tie command, & tie, and
% tie commands are all valid and equivalent.
Rmm X2$ •Spr X2@]
Example: +7*3P12*7&11*5&4*5%6*6! Esc
Brackets are shown to separate ties for clarity
only. Create preset 3 for room 7, which ties
input 12 to output 7, input 11 to output 5,
input 4 to output 5, and input 6 to output 6.
RmmØ7•SprØ3 ]
Lock (executive) modes
NOTE: See “ Setting the Front Panel Locks (Executive Modes) ” in the Operation section for more information on the Lock modes.
Lock all front panel
functions 1X Exe1 ] Enable Lock mode 1.
Lock advanced front panel
functions 2X Exe2 ] Enable Lock mode 2.
Unlock all front panel
functions ØX ExeØ ] Enable Lock mode 0.
View lock status X X1#]
NOTE: X! = Input number 00 – maximum number of inputs for your matrix size (00 = untied)
X@ = Output number 01 – (maximum number of outputs for your matrix size)
X1# = Lock status 0 = Lock mode 0 1 = Lock mode 1 2 = Lock mode 2
X2@ = Global or room preset number 01 – 64 (global) or 01 – 10 (room)
X2# = Name 12 characters maximum
Upper- and lower-case alphanumeric characters and _ / and spaces are valid.
X2$ = Room number (for room presets) 01 – 10
MTPX Plus 6400 Series Matrix Switchers • Programming Guide 78