Document Outline

• N9340A Overview
  • Introduction
    • Functionality
    • Enhanced Usability
  • Front Panel Overview
  • Top Panel Overview
  • Display Annotations
  • Working with Batteries
    • Installing a Battery
    • Viewing Battery Status
    • Charging a Battery
• Getting Started
  • Checking Shipment and Order List
  • Power Requirements
  • AC Power Cords
  • Safety Considerations
    • Environmental Requirements
    • Electrical Requirements
    • Electrostatic Discharge (ESD) Precautions
    • Instrument Markings
  • Power on the Analyzer for the First Time
    • Power on your N9340A
  • Preparation for Use
    • Setting up your N9340A
    • Testing key stroke and screen pixel
    • Checking Instrument Information
  • Making a Basic Measurement
    • Viewing a Signal
      • Figure 1 View a signal (1 GHz, 0 dBm)
    • Some helpful tips
  • Contact Agilent Technologies
• System Setting
  • Visual and Audio Adjustment
    • Quick Display Adjustment
    • Manual Display Adjustment
    • Setting Key Beep
  • System Setting
    • General system settings
    • Ext Input
  • File
    • Saving a file
    • Deleting a file
    • Loading a file
  • Show System
  • Show Error
  • Perform a Time Base Calibration
  • Preset
  • Factory Default Settings
• Making Measurements
  • Measuring Multiple Signals
    • Comparing Signals on the Same Screen
      • Figure 2 Delta pair marker with signals on the same screen
    • Resolving Signals of Equal Amplitude
      • Figure 3 Setup for obtaining two signals
    • Resolving Small Signals Hidden by Large Signals
  • Measuring a Low-Level Signal
    • Reducing Input Attenuation
      • Figure 4 A signal closer to the noise level (Atten:10 dB)
      • Figure 5 A signal closer to the noise level (Atten:20 dB)
      • Figure 6 A signal closer to the noise level (Atten: 0 dB)
    • Decreasing the Resolution Bandwidth
      • Figure 7 Decreasing Resolution Bandwidth
    • Using the Average Detector and Increased Sweep Time
      • Figure 8 Using the Average Detector
    • Trace Averaging
      • Figure 9 Trace Averaging
  • Improving Frequency Resolution and Accuracy
    • Figure 10 Using Frequency Counter
  • Making Distortion Measurements
    • Identifying Analyzer Generated Distortion
      • Figure 11 Harmonic Distortion
      • Figure 12 Identifying Analyzer Distortion (O dB atten)
      • Figure 13 Identifying Analyzer Distortion (10 dB atten)
  • Third-Order Intermodulation Distortion
  • Measuring Phase Noise
    • Figure 14 Measuring Phase Noise (1)
    • Figure 15 Measuring Phase Noise (2)
  • One Button Measurement
    • Measuring OBW
    • Measuring ACPR
    • Measuring Channel Power
• Key Reference
  • Amplitude
    • Ref level
    • Attenuation
    • Preamp
    • Scale/DIV
    • Scale Type
    • Ref Offset
    • Y Axis Units
  • BW/SWP
    • RBW
    • VBW
    • VBW/RBW
    • Avg Type
    • Sweep Time
    • Sweep
  • Enter
  • ESC/CLR
  • Frequency
    • Center Frequency
    • Start Frequency
    • Stop Frequency
    • CF Step
  • Marker
    • Marker
    • Normal
    • Delta
    • Off
    • Peak Search
    • Marker To
    • Mode
    • Marker Trace
    • All Off
  • Meas
  • Span
    • Span
    • Full
    • Zero
    • Last Span
  • TRACE
    • Trace
    • Clear Write
    • Max Hold
    • Minimum Hold
    • View
    • Blank
    • Detector
    • Average
    • Save Trace
    • Save As
    • Recall Trace
  • Limit
    • Limit Line
    • Limit Pattern
    • Set Pattern
    • Limit Type
    • Beep
    • Save Pattern
    • Recall Pattern
• SCPI Command Reference
  • SCPI Language Basics
    • Basic Knowledge Requirement
    • Command Categories
    • Command Syntax
    • Standard Notations
  • Common Commands
    • Clear Status
    • Identification Query
    • Reset
  • CALCulate Subsystem
    • CALCulate:LLINe Subsection
    • CALCulate:MARKer Subsection
  • DEMOdulation Subsystem
    • AM Demodulation
    • FM Demodulation
  • DISPlay Subsystem
    • Turn the Entire Display On/Off
    • Trace Y-Axis Scaling
    • Trace Y-Axis Reference Level
    • Trace Y-Axis Reference Level Offset
    • Vertical Axis Scaling
    • Screen Color Style
    • Display Mode
    • Contrast
    • Brightness
  • INITiate Subsystem
    • Continuous or Single Measurements
    • Take New Data Acquisitions
  • INSTrument Subsystem
    • Select One button measurement
  • MEASure Subsystem
    • OBW Subsection
    • ACPR Subsection
    • Channel Power Subsection
  • SENSe Subsystem
    • [:SENSe]:AVERage Subsection
    • [:SENSe]:BANDwidth Subsection
    • [:SENSe]:DETector Subsection
    • [:SENSe]:FREQuency Subsection
    • [:SENSe]:POWer Subsection
    • [:SENSe]:SWEep Subsection
  • SYSTem Subsystem
    • Ext Input
    • Date Query
    • Time Query
    • Error Information Query
  • TRACe Subsystem
  • TRIGer Subsystem
    • External Trigger Slope
    • Trigger Source
    • Video Trigger Level Amplitude
  • UNIT Subsystem
• Error Messages
  • Error Message List
• Menu Map
  • AMPTD
  • BW/SWP
  • FREQ
  • MARKER
  • MEAS
  • SPAN
  • SYS
  • TRACE
  • Limit