H3C Technologies H3C S10500 Series Switches User Manual
High availability configuration guide
Advertising
This manual is related to the following products:
H3C S5800 Series Switches, H3C S5820X Series Switches, H3C WX3000E Series Wireless Switches, H3C SecPath F1000-E, H3C SecPath F5000-A5 Firewall, H3C SecPath F1000-A-EI, H3C SecPath F1000-E-SI, H3C SecPath F1000-S-AI, H3C SecPath F5000-S Firewall, H3C SecPath F5000-C Firewall, H3C SecPath F100-C-SI, H3C SecPath F1000-C-SI, H3C SecPath F100-A-SI, H3C SecBlade FW Cards, H3C SecBlade FW Enhanced Cards, H3C SecPath U200-A U200-M U200-S, H3C SecPath U200-CA U200-CM U200-CS
Table of contents
Document Outline
- Title Page
- Preface
- Contents
- High availability overview
- Active and standby switchover configuration
- Ethernet OAM configuration
- CFD configuration
- DLDP configuration
- DLDP overview
- DLDP configuration task list
- Configuring the duplex mode and speed of an Ethernet interface
- Enabling DLDP
- Setting DLDP mode
- Setting the interval to send advertisement packets
- Setting the delaydown timer
- Setting the port shutdown mode
- Configuring DLDP authentication
- Resetting DLDP state
- Displaying and maintaining DLDP
- DLDP configuration examples
- Troubleshooting DLDP
- RRPP configuration
- RRPP overview
- RRPP configuration task list
- Creating an RRPP domain
- Configuring control VLANs
- Configuring protected VLANs
- Configuring RRPP rings
- Activating an RRPP domain
- Configuring RRPP timers
- Configuring RRPP fast detection
- Configuring an RRPP ring group
- Displaying and maintaining RRPP
- RRPP configuration examples
- Troubleshooting
- Smart Link configuration
- Smart Link overview
- Smart Link configuration task list
- Configuring a Smart Link device
- Configuring an associated device
- Displaying and maintaining Smart Link
- Smart Link configuration examples
- Monitor Link configuration
- VRRP configuration
- VRRP overview
- VRRP standard protocol mode
- Configuring VRRP for IPv4
- VRRP for IPv4 configuration task list
- Specifying the type of MAC addresses mapped to virtual IP addresses
- Creating a VRRP group and configuring virtual IP address
- Configuring router priority, preemptive mode and tracking function
- Configuring VRRP packet attributes
- Enabling the trap function for VRRP
- Displaying and maintaining VRRP for IPv4
- Configuring VRRP for IPv6
- VRRP for IPv6 configuration task list
- Specifying the type of MAC addresses mapped to virtual IPv6 addresses
- Creating a VRRP group and configuring a virtual IPv6 address
- Configuring router priority, preemptive mode and tracking function
- Configuring VRRP packet attributes
- Displaying and maintaining VRRP for IPv6
- IPv4-based VRRP configuration examples
- IPv6-based VRRP configuration examples
- Troubleshooting VRRP
- BFD configuration
- Track configuration
- Track overview
- Track configuration task list
- Associating the track module with a detection module
- Associating the track module with an application module
- Displaying and maintaining track entries
- Track configuration examples
- VRRP-track-NQA collaboration configuration example (the master monitors the uplink)
- Configuring BFD for a VRRP backup to monitor the master
- Configuring BFD for the VRRP master to monitor the uplinks
- Static routing-track-NQA collaboration configuration example
- Static routing-Track-BFD collaboration configuration example
- VRRP-track-interface management collaboration configuration example (the master monitors the uplink interface)
- Index