Roland V-160HD SDI/HDMI Streaming Video Switcher - Manual (Page 45)

45
Audio Operations
Outputting AUX-bus Audio
The V-160HD has two types audio buses: MASTER OUTPUT and AUX. You can assign a desired bus to each output connector.
Audio bus Explanation
MASTER
OUTPUT
All input audio is mixed and output (master output).
AUX
This mixes and outputs only the input audio that is sent to
the AUX bus. This allows you to output audio that is different
than the master output.
For example, in a live event, you might output a mix of all
audio inputs, while separately outputting a mix of only
specific audio inputs (the AUX bus) for recording or streaming.
Assigning the AUX Bus
AUDIO OUT jacks, PHONES jack, USB STREAM port
1 . [MENU] button
Ó
“AUDIO OUTPUT”
Ó
“OUTPUT ASSIGN”
Ó
select the output jack, and press the [VALUE] knob.
2 . Use the [VALUE] knob to select “AUX,” and press the
[VALUE] knob.
Value Explanation
MASTER OUTPUT Output the audio of the MASTER OUTPUT bus.
AUX Output the audio of the AUX bus.
3 . Press the [MENU] button to close the menu.
HDMI OUT and SDI OUT connectors
1 . [MENU] button
Ó
“AUDIO OUTPUT”
Ó
“OUTPUT ASSIGN”
Ó
select the output connector, and press the [VALUE] knob.
2 . Use the [VALUE] knob to select “AUX” or “AUTO,” and press
the [VALUE] knob.
Value Explanation
AUTO
The audio bus automatically switches according
to the video bus assignment (p. 14).
Video bus Audio bus
Others besides AUX MASTER OUTPUT
AUX AUX
MASTER OUTPUT Output the audio of the MASTER OUTPUT bus.
AUX Output the audio of the AUX bus.
3 . Press the [MENU] button to close the menu.
Sending Audio to the AUX Bus
* Use the [AUX] knob to adjust the volume of audio output from the
AUX bus.
1 . [MENU] button
Ó
“AUDIO OUTPUT”
Ó
“AUX”
Ó
select
“AUX SEND,” and press the [VALUE] knob.
The AUX SEND menu appears.
2 . Use the [VALUE] knob to select the input audio, and press
the [VALUE] knob.
* You can select HDMI IN and SDI IN by setting “AUX SEND VIDEO” to
“MANUAL.”
When this is set to “AUTO,” the audio is automatically sent to the
AUX bus in tandem with the AUX bus video selection.
3 . Use the [VALUE] knob to adjust the amount that is sent to
the AUX bus, and press the [VALUE] knob.
4 . Press the [MENU] button to close the menu.
Setting the character of the sound
You can select whether to send either the original audio or the audio
processed with effects to the AUX bus.
1 . [MENU] button
Ó
“AUDIO OUTPUT”
Ó
“AUX”
Ó
select
“AUX EFFECT,” and press the [VALUE] knob.
The AUX EFFECT menu appears.
2 . Use the [VALUE] knob to select the input audio, and press
the [VALUE] knob.
3 . Use the [VALUE] knob to select “DRY,” “PRE FADE,” or
“POST FADER,” and press the [VALUE] knob.
Value Explanation
DRY Sends the source audio with no effects applied.
PRE FADER
Sends the effect-applied audio.
The send volume is constant, regardless of the volume
(INPUT LEVEL).
POST FADER
Sends the effect-applied audio.
The send volume can be changed by adjusting the
volume (INPUT LEVEL).
4 . Press the [MENU] button to close the menu.