V-Tech CAT5 System Technical Guide - Manual (Page 79)

Page 79 K5 System Technical Guide
Work with C5-MDS
This example contains the full function available in the system:
Multi entrances with C5-MDS; Monitor display network video; and one of the monitor serves as
Guard Monitor.
JWB(IN4)
P- P+ P- P+ PA S1
1
ON DIP
2 3 4 5 6
JWB(IN3) JWB(IN2) JWB(IN1) JWB(OUT)
T/R- ERROR INUSE LINK POWER T/R+
P- P+ P+ P-
1 2 3
6 5 4
7 8 9
# 0 *
RF CARD
CN1 CN2
CN-LK
J/KMB JP-LK
Bus EB+ EB- N.O LK+ LK- +12V
1 2 3
T/R- T/R+
1 2 3
P+ P- P+ P- RS485
SW1
JWB(IN) JWB(OUT) CN(MDS) ETHERNET
PA VR600
+
S1 POWER LINK IN-USE
AG
1
ON
ON
DIP
DIP
2 3 4 5 6
1 2 3
P+ P+ P- RS485
SW1
JWB(OUT) ETHERNET
C5-IPC
IP-MR18
+ -
+ -
PS5
AC + -
F4/F4DV/F4Q
ON DIP
Remove 3 jumpers LAN
Note that ID Code(#8001-1) setting in
MR18 must be set to 2
1 2 3
6 5 4
7 8 9
# 0 *
RF CARD
CN1 CN2
CN-LK
J/KMB JP-LK
Bus EB+ EB- N.O LK+ LK- +12V
1 2 3
T/R- T/R+
IP-MR18
+ -
Note that ID Code(#8001-1) setting in
MR18 must be set to 1
JWB(IN)
+ -
JWB(IN4) JWB(IN3) JWB(OUT)
P-
JWB(IN2) JWB(IN1)
1V 4A/2V 2A/1V 1A
CN(MDS)
1 2
3 4
C5-AT27
C5-F414
To other monitors
PS5
AC + -
1R 2W
GD VD T/R+ T/R- Z1 Z2 Z3 Z4 COM COM PR
3Y 4B FV+ FV- P- AU P- P+ P+ D1&D2
To Next C5-F414
PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT)
VD-SET(L=HIGH)
P- P+ P- P+ PA S1
1
ON
2
T/R- ERROR INUSE LINK POWER T/R+
PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT)
+ -
P- P+ P+ P-
VD-SET
HI / VD
1
2 3
4
C5-AT27
C5-F414
To other monitors
1R 2W
GD VD T/R+ T/R- Z1 Z2 Z3 Z4 COM COM PR
3Y 4B FV+ FV- P- AU P- P+ P+ D1&D2
PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT)
VD-SET(L=HIGH)
P- P+ P- P+ PA S1
1
ON
2
T/R- ERROR INUSE LINK POWER T/R+
PORT-A PORT-B PORT-C PORT-D JWB(OUT)
+ -
P- P+ P+ P-
VD-SET
HI / VD
+ -
To Next PS5
Note that VD-SET must be set to VD if the C5-F414 is the last one of the bus
HI / VD
JWB(IN)
CAT5
RVV2*1.0mm
A single cable to connect
P-(Ground) together
C5-MDS
1 2 3 4
Note:
1. C5-MDS needed to be connected to the CN-MDS port of C5-IPC
2. The 3 jumpers on C5-IPC must be removed.