Yokogawa Touch Screen GP20 - Manual (Page 40)

2-26
IM 04L51B01-17EN
SAlmMarkCom
Alarm Mark (/MC)
Sets the display of the marker that indicates the specified
alarm position of a communication channel.
Syntax SAlmMarkCom,p1,p2,p3,p4,p5,p6,p7,p
8,p9,p10,p11,p12,p13,p14,p15
p1 Channel number
p2 Whether to display the alarm mark on the
scale (Off, On)
p3 Alarm mark type
Alarm Display the default alarm mark
Fixed Display the mark with the
specified color
P4 R value of the RGB mark colors for alarm
1 ( 0 to 255)
p5 G value of the RGB mark colors for alarm
1 ( 0 to 255)
p6 B value of the RGB mark colors for alarm
1 ( 0 to 255)
p7 R value of the RGB mark colors for alarm
2 ( 0 to 255)
p8 G value of the RGB mark colors for alarm
2 ( 0 to 255)
p9 B value of the RGB mark colors for alarm
2 ( 0 to 255)
p10 R value of the RGB mark colors for alarm
3 ( 0 to 255)
p11 G value of the RGB mark colors for alarm
3 ( 0 to 255)
p12 B value of the RGB mark colors for alarm
3 ( 0 to 255)
p13 R value of the RGB mark colors for alarm
4 ( 0 to 255)
p14 G value of the RGB mark colors for alarm
4 ( 0 to 255)
p15 B value of the RGB mark colors for alarm
4 ( 0 to 255)
Query SAlmMarkCom[,p1]?
Example Display the alarm marks for alarms 1 to 4 of
communication channel 025 in fixed colors red,
brown, orange, and yellow, respectively.
SAlmMarkCom,025,On,Fixed,255,0,0,
165,42,42,255,165,0,255,255,0
Description
• For details on RGB values, see “Description” of the
SColorIO command.
SAlmLimit
Rate-of-Change Alarm Interval
Sets the rate-of-change interval of the rate-of-change
alarm.
Syntax SAlmLimit,p1,p2
p1 Interval for the low limit on rate-of-change
alarm
1 to 32 Integer multiple of the scan
interval
p2 Interval for the high limit on rate-of-change
alarm
1 to 32 Integer multiple of the scan
interval
Query SAlmLimit?
Example Set the intervals for the low limit on rate-of-
change alarm and high limit on rate-of-change
alarm to 10 times and 20 times the scan
interval, respectively.
SAlmLimit,10,20
Description
• You cannot use this command to configure settings
while recording is in progress.
• You cannot use this command to configure settings
while computation is in progress.
SAlmSts
Alarm Display Hold/Nonhold
Sets the alarm display hold/nonhold operation.
Syntax SAlmSts,p1
p1 Operation
Hold
NonHold
Query SAlmSts?
Example Hold the alarm display until an alarm ACK
operation.
SAlmSts,Hold
Description
• You cannot use this command to configure settings
while recording is in progress.
• You cannot use this command to configure settings
while computation is in progress.
STimer
Timer
Sets a timer.
Do Not Use Timers
Syntax STimer,p1,p2
p1 Timer number (1 to 4)
p2 Timer type (Off)
Relative Timer
Syntax STimer,p1,p2,p3,p4,p5,p6
p1 Timer number (1 to 4)
p2 Timer type (Relative)
p3 Interval: Days (0 to 31)
P4 Interval: Hours (HH) (00 to 23)
p5 Interval: Minutes (MM) (00 to 59)
p6 Reset on Math start (Off, On)
Absolute Timer
Syntax STimer,p1,p2,p3,p4,p5
p1 Timer number (1 to 4)
p2 Timer type (Absolute)
p3 Interval (1min, 2min, 3min, 4min, 5min,
6min, 10min, 12min, 15min, 20min,
30min, 1h, 2h, 3h, 4h, 6h, 8h, 12h, 24h)
P4 Reference time: Hours (HH) (00 to 23)
p5 Reference time: Minutes (MM) (00 to 59)
Query STimer[,p1]?
2.4 Setting Commands