KYORITSU 6300 Instruction Manual - Manual (Page 49)

4. 23
MODEL6300
Section 4 Setting MODEL6300
‣ ‧•⁈ ‥• •⁈ •• ⁈ ‣ ⁂․ ⁉ ‣ ⁂‥ ⁉ ‥⁂ ‥⁉ ‥ ⁂…⁉
‧ ″ ‣ •″ ․ •″ ‧• ″ ‣•• ″ ․•• ″ ‧• •″ ‣• ••″
4-3-19 “Setting 19” Use of CF card
For the detailed information about CF card, refer to “Section 9: CF card/
Internal memory” in this manual.
* Using the Cursor key whilst in the selection screen, select “Setting 19”.
* Press the ENTER key to enter setting change mode.
<With the CF card placed in the instrument>
* “rEC.on” is displayed on LCD. [“on” (when using a CF card) will flicker]
* Notwithstanding the presence of the CFcard, if the data is to be saved to
the internal memory, press
Cursor key to change the indication into “oFF”.
(“oFF”:i.e. not using a CF card). Otherwise this step is to be ignored.
* Then press the
ENTER key.








<Without CF card >
* “rEC.oFF” is displayed on LCD (“oFF” will flicker). This cannot be altered.
The measured data is automatically saved to the internal memory.

NOTE
* The instrument automatically identifies a CF card when it is turned on.
* If necessary, check the condition of the CF card on other hardware.
* Refer to the CF card instruction manual for further details on the card.
CAUTION
Always set the Function switch to the OFF position before inserting/
removing a CF card. If a CF card is inserted/removed with the instrument
on, saved data may be lost or instrument may be damaged.
‣ ‧•⁈ ‧•⁈ ‥• ‥• •⁈ •⁈ •• •• ⁈ ‣ ⁂․ ⁉ ‣ ⁂‥ ⁉ ‥⁂ ‥⁂ ‥⁉ ‥⁉ ‥ ⁂…⁉ …⁉
‧ ″ ‣ •″ •″ ․ •″ •″ ‧• ‧• ″ ‣•• ‣•• ″ ․•• ․•• ″ ‧• ‧• •″ •″ ‣• ‣• ••″ ••″
‣ ‧ ‣ ‧•⁈ ‥• • • •⁈ •• ⁈ • ⁈ ‣ ⁂ ‣ ⁂․ ⁉ ․ ⁉ ‣ ⁂ ‣ ⁂‥ ⁉ ‥ ⁉ ‥⁂ ‥⁉ ‥ ⁂ ‥ ⁂…⁉
‧ ″ ‧ ″ ‣ • ‣ •″ ․ • ․ •″ ‧• ″ • ″ ‣•• ″ • ″ ․•• ″ • ″ ‧• • • •″ ‣• • • ••″
any of
‣ ‧•⁈ ‥• •⁈ •• ⁈ ‣ ⁂․ ⁉ ‣ ⁂‥ ⁉ ‥⁂ ‥⁉ ‥ ⁂…⁉
‧ ″ ‣ •″ ․ •″ ‧• ″ ‣•• ″ ․•• ″ ‧• •″ ‣• ••″
‣ ‧•⁈ ‥• •⁈ •• ⁈ ‣ ⁂․ ⁉ ‣ ⁂‥ ⁉ ‥⁂ ‥⁉ ‥ ⁂…⁉
‧ ″ ‣ •″ ․ •″ ‧• ″ ‣•• ″ ․•• ″ ‧• •″ ‣• ••″