KYORITSU 6300 Instruction Manual - Manual (Page 50)

MODEL6300
4. 24
MODEL6300 Section 4 Setting
Section
4
‣ ‧•⁈ ‧•⁈ ‥• ‥• •⁈ •⁈ •• •• ⁈ ‣ ⁂․ ⁉ ‣ ⁂‥ ⁉ ‥⁂ ‥⁂ ‥⁉ ‥⁉ ‥ ⁂…⁉ …⁉
‧ ″ ‣ •″ •″ ․ •″ •″ ‧• ‧• ″ ‣•• ‣•• ″ ․•• ․•• ″ ‧• ‧• •″ •″ ‣• ‣• ••″ ••″






4-3-20 “Setting 20” Formatting CF card
A new CF card has to be formatted before use.
For the detailed information about the CF card, refer to “Section 9: CF card/
Internal memory” in this manual.
* Confirm that the Function switch is in the OFF position, and insert the CF
card into the CF card connector of the instrument.
* Set the Function switch to
SET UP range.
* Using the Cursor key whilst in the selection screen, select “Setting 20”.
* Press the ENTER key to enter setting change mode.
* The message “oFF”(i.e. not formatted) will flicker. Change it to
“on”(formatted) with the
Cursor key. If the CF card is not inserted, it cannot
be set to “on”.
On pressing the ENTER key, formatting will start. Formatting takes a few
seconds. After formatting is complete, a message “InIt. FInISh” is displayed
on the LCD.
CAUTION
Always set the Function switch to the OFF position before inserting/
removing a CF card. If a CF card is inserted/removed while the instrument
is on, saved data may be lost or the instrument may be damaged.
‣ ‧•⁈ ‥• •⁈ •• ⁈ ‣ ⁂․ ⁉ ‣ ⁂‥ ⁉ ‥⁂ ‥⁉ ‥ ⁂…⁉
‧ ″ ‣ •″ ․ •″ ‧• ″ ‣•• ″ ․•• ″ ‧• •″ ‣• ••″
‣ ‧•⁈ ‥• •⁈ •• ⁈ ‣ ⁂․ ⁉ ‣ ⁂‥ ⁉ ‥⁂ ‥⁉ ‥ ⁂…⁉
‧ ″ ‣ •″ ․ •″ ‧• ″ ‣•• ″ ․•• ″ ‧• •″ ‣• ••″
‣ ‧•⁈ ‧•⁈ ‥• ‥• •⁈ •⁈ •• •• ⁈ ‣ ⁂․ ⁉ ‣ ⁂‥ ⁉ ‥⁂ ‥⁂ ‥⁉ ‥⁉ ‥ ⁂…⁉ …⁉
‧ ″ ‣ •″ •″ ․ •″ •″ ‧• ‧• ″ ‣•• ‣•• ″ ․•• ․•• ″ ‧• ‧• •″ •″ ‣• ‣• ••″ ••″
‣ ‧ ‣ ‧•⁈ ‥• • • •⁈ •• ⁈ • ⁈ ‣ ⁂ ‣ ⁂․ ⁉ ․ ⁉ ‣ ⁂ ‣ ⁂‥ ⁉ ‥ ⁉ ‥⁂ ‥⁉ ‥ ⁂ ‥ ⁂…⁉
‧ ″ ‧ ″ ‣ • ‣ •″ ․ • ․ •″ ‧• ″ • ″ ‣•• ″ • ″ ․•• ″ • ″ ‧• • • •″ ‣• • • ••″
any of