FanAm MD60 AC Drive - Manual (Page 36)

6-4 MD60 AC Drive User Manual
6.4 Wiring the Control Terminal Block
No. Signal Default Description Parameter
R1 Relay N.O. Fault Normally open contact for output relay. A055
R2 Relay Common – Common for output relay.
R3 Relay N.C. Fault Normally closed contact for output relay. A055
Sink/Source DIP Switch Source (SRC) Inputs can be wired as Sink (SNK) or Source (SRC) via DIP Switch setting.
01 Stop
(1)
Coast
The factory-installed jumper or a normally closed input
must be present for the drive to start.
P036
02 Start/Run FWD Not Active Command comes from the integral keypad by default. To
disable reverse operation, see A095 (Reverse Disable). P036, P037
03 Dir/Run REV Not Active P036, P037, A095
04 Digital Common –
For digital inputs. Electronically isolated with digital
inputs from analog I/O.
05 Digital Input 1 Preset 1 Program with A051 (Digital In1 Select). A051
06 Digital Input 2 Preset 2 Program with A052 (Digital In2 Select). A052
11 +24V DC – Drive supplied power for digital inputs.
12 +10V DC – Drive supplied power for 0-10V external potentiometer. P038
13 0-10V In (3) Not Active
For external 0-10V input supply
(input impedance = 100k ohm) or potentiometer wiper.
P038
14 Analog Common –
For 0-10V In or 4-20mA In. Analog inputs electrically
isolated from digital I/O.
15 4-20mA In (3) Not Active
For external 4-20mA input supply
(input impedance = 250 ohm).
P038
16 RS485 Shield –
Terminal should be connected to chassis ground when
using the RS485 communications port.
(3)
Only one analog frequency source may be connected at a time. If more than one reference is connected at the same time,
an undetermined frequency reference will result.
( 4) RS485 port is used to connect the drive to a personal computer running VS Utilities via a Serial Converter module, and for
connection to the Remote Nema 4x/12 or Copy Cat Keypads.
Figure 6.1 – Wiring the Control Terminal Block
30V DC 125V AC 230V AC
Resistive 3.0A 3.0A 3.0A
Inductive 0.5A 0.5A 0.5A
(1) Important: I/O Terminal 01
is always a coast-to-stop input
except when P036 (Start Source)
is set to 3-Wire Control. In three-
wire control, I/O Terminal 01 is
controlled by P037 (Stop
Mode).
All other sources are
controlled by
P037 (Stop Mode).
Important: The drive is
shipped with a jumper
installed between I/O
Terminals 01 and 11.
Remove this jumper when
using I/O Terminal 01 as a
stop or enable input.
(2) Two-wire control shown.
For three-wire control, use a
momentary input
on
I/O Terminal 02 to command
a start. Use a maintained
input
for I/O Terminal
03 to change direction.
P036 (Start Source) Stop I/O Terminal 01 Stop
Keypad Per P037 Coast
3-Wire Per P037 Per P037
2-Wire Per P037 Coast
RS485 Per P037 Coast
01
02
03
04
05
06
11
12
13
14
15
16
Stop
(1)
Start/Run FWD
(2)
Direction/Run REV
Digital Common
Digital Input 1
Digital Input 2
R1
R2
R3
Relay N.O.
Relay Common
Relay N.C.
+24V DC
+10V DC
0-10V In
Analog Common
4-20mA In
RS485 Shield
+24V
+10V
SRC SNK
Typical
SNK Wiring
Typical
SRC Wiring
1 8
RS485
(DSI)
R1 R2 R3
01 02 03 04 05 06
11 12 13 14 15 16 SNK
SRC (1)