3 performance data, Turning radius (outside), Turning radius (inside) – JLG 600SC_660SJC Service Manual User Manual

Page 14: Boom elevation, Machine weight approximately, Machine height (stowed), Machine length (stowed), Machine width, 4 function speeds, Machine orientation when doing speed tests

Advertising
background image

SECTION 1 - SPECIFICATIONS

1-2

– JLG Lift –

3120898

1.3

PERFORMANCE DATA

Travel Speed

1.6 MPH (2.6 Km/hr.)

Travel Speed - Out of Transport

0.4 MPH (0.6 Km/hr.)

Gradeability.

55%

Turning Radius (Outside)

8 ft. (2.4 m)

Turning Radius (Inside)

0

Boom Elevation

600SC - +60 ft. 2 13/16 in. (18.36 m)

-6 ft. 1 11/16 in. (1.87 m)

600SCJ - +60 ft. 5 3/4 in. (18.43 m)

-9 ft. 9 3/16 in. (2.98 m)

660SCJ - +66 ft. 7 5/8 in. (20.31 m)

-11 ft. 5 1/4 in. (3.49 m)

Machine Weight approximately

Steel Track - 25,900 lbs. (11,748 kg)

Rubber Track - 26,860 lbs. (12,184 kg)

Machine Height (Stowed)

Steel Track - 8’4" (2.54 m)

Rubber Track - 8’6" (2.59 m)

Machine Length (Stowed)

35’ 6" (10.8 m)

Machine Width

8 ft. (2.4 m)

1.4

FUNCTION SPEEDS

Machine Orientation When Doing Speed
Tests

Lift: Telescope Retracted. Lift Up, Record Time, Lift Down,
Record Time.

Swing: Boom at Full Elevation. Telescope Retracted.
Swing the Turntable off center and stop. Swing the oppo-
site direction ana start the test wen the turntable is cen-
tered up. This eliminates ramp up and down on the
controller affecting times.

Telescope: Boom at Full Elevation; Telescope Retracted;
Telescope Out, Record Time. Telescope In, Record Time.

Tracking: Test to be done on a gravelled level surface.
Position the machine driving at high speed at a reference
point. (No steer correction). Results should be 4 to 6
ft.(1.2 to 1.8 m) tracking error at 200 ft. (60.9 m).

Drive: Test should be done on a graveled level surface.
Drive select switch should be set at High Speed. Start
approx. 10 ft. from starting point so that the unit is at max-
imum speed when starting the test. Results should be
recorded for a 200 ft. (60.9 m) course. Drive Forward,
Record Time. Drive Reverse, Record Time.

Drive (Out of Transport): Test should be done on a grav-
eled level surface. Drive select switch should be set at
Low Engine, Low Drive (The platform speed knob control,
if equipped, could be selected to the creep speed to simu-
late the boom above horizontal). Results should be
recorded for a 50 ft. (15.2 m) course. Drive Forward,
Record Time. Drive Reverse, Record Time.

Table 1-1. Function Speeds (In Seconds)

Function

Speed

Lift Up

46-60

Lift Down

33-43

Swing Right & Left*

79-101

Telescope In

22-33

Telescope Out

50-67

Platform Rotate Right & Left**

16-25

Jib Up

22-34

Jib Down

16-26

Drive (Forward & Reverse)

85-90

Drive Out of Transport (Forward & Reverse)

80-85

*Max 10% Difference Between Left & Right
**Max 15% Difference Between Left & Right

Advertising