Document Outline

• 1 Introduction
  • 1.1 Available technical documentation
    • 1.1.1 General information
    • 1.1.2 Base units
    • 1.1.3 Input/output modules
    • 1.1.4 Special modules
    • 1.1.5 Operating, visualization, recording
    • 1.1.6 Power supply units
  • 1.2 Safety information
    • 1.2.1 Warning symbols
    • 1.2.2 Note signs
    • 1.2.3 Intended use
    • 1.2.4 Qualification of personnel
  • 1.3 Acceptance of goods, storage, and transport
    • 1.3.1 Checking the delivery
    • 1.3.2 Notes on storage and transport
    • 1.3.3 Returning goods
    • 1.3.4 Disposal
  • 1.4 Identifying the device version
    • 1.4.1 Nameplate
    • 1.4.2 Order details
    • 1.4.3 Delivery package
    • 1.4.4 Accessories
    • 1.4.5 General accessories
  • 1.5 System version
• 2 Description
  • 2.1 Brief description
  • 2.2 Block diagram
• 3 Installation
  • 3.1 General information on installation/dismounting
  • 3.2 Installation/dismounting on DIN rail
    • 3.2.1 Base units
  • 3.3 Dimensions
• 4 Electrical connection
  • 4.1 Installation notes
  • 4.2 Electrical isolation
  • 4.3 Connection diagram
    • 4.3.1 Display, operating, and connection elements
    • 4.3.2 Interfaces
    • 4.3.3 Voltage supply
    • 4.3.4 Terminating resistors
  • 4.4 Functional check
• 5 Operation
  • 5.1 Display, operating, and connection elements
  • 5.2 System states
  • 5.3 System switch
  • 5.4 LED displays
    • 5.4.1 Display modes
    • 5.4.2 System states and errors
  • 5.5 Operation on the multifunction panel
    • 5.5.1 Program generator
• 6 Configuration
  • 6.1 Selectors
    • 6.1.1 Analog selector
    • 6.1.2 Digital selector
  • 6.2 Device data
    • 6.2.1 Setup info
  • 6.3 Variables
    • 6.3.1 Analog variables
    • 6.3.2 Integer variables
    • 6.3.3 Digital variables
    • 6.3.4 Text variables
  • 6.4 Limit value monitoring
    • 6.4.1 Alarm
    • 6.4.2 Alarm and hysteresis functions
  • 6.5 Binary links
  • 6.6 Modbus/TCP
  • 6.7 Serial interface
    • 6.7.1 Modem
  • 6.8 PROFIBUS (version 02)
  • 6.9 Web server
  • 6.10 PLC configuration
  • 6.11 Program generator
    • 6.11.1 General
    • 6.11.2 Setpoint limits
    • 6.11.3 Basic status setpoints
    • 6.11.4 Manual mode setpoints
    • 6.11.5 Setpoint specification
    • 6.11.6 Names of operating contacts
    • 6.11.7 Tolerance band monitoring
    • 6.11.8 Events
    • 6.11.9 Process screen
• 7 Parameterization
  • 7.1 PLC parameter
• 8 Configuration – in setup program only
  • 8.1 E-mail
    • 8.1.1 E-mail server
  • 8.2 Modbus frames for reading
  • 8.3 Modbus frames for writing
  • 8.4 Analog PLC output texts
  • 8.5 Integer PLC output texts
  • 8.6 Digital PLC output texts
  • 8.7 Texts
• 9 Program editor
  • 9.1 General information
  • 9.2 Program schema
  • 9.3 Program simulation
  • 9.4 Process steps (as of version 02)
  • 9.5 License dependance
    • 9.5.1 "Program editor" license
• 10 Online parameters
  • 10.1 Ethernet
  • 10.2 System bus
  • 10.3 Enabling of extra codes
  • 10.4 Resetting the user list
  • 10.5 Date and time
  • 10.6 Calibrate / test
    • 10.6.1 LED test
    • 10.6.2 Switch test
    • 10.6.3 Versions
    • 10.6.4 Battery
• 11 Retrofitting interfaces
• 12 Appendix
  • 12.1 Technical data
    • 12.1.1 Interfaces
    • 12.1.2 Electrical data
    • 12.1.3 Case and ambient conditions
    • 12.1.4 Approval/approval marks
  • 12.2 Cycle time, sampling rate, and shut-down time
  • 12.3 Resources for customer specific PLC programs