Lenze E84DGFCA - Manual (Page 70)

Index
70
Lenze · Decentralised frequency inverter 8400 motec (AS-Interface option) · EDS84DMOTASI EN 4.0 - 09/2013
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
A
Accessing process data 39
Active address (C13200) 61
Acyclic parameter data channel 17
Addressing the AS-i slaves 26
All words from standard device (C13853) 66
All words to standard device (C13852) 66
Application as directed 12
Application notes (representation) 9
Approvals 16
AS-i: monitoring times (C13208) 63
AS-i bus transaction counter (C13210) 63
AS-i concept of the Communication Unit 33
AS-i connection 22
AS-i error messages: Causes and remedies 56
AS-i error messages (short overview) 55
AS-i profile 7.A.5 34
AS-i profile 7.A.E 36
B
Baud rate 16
Before initial switch-on 24
Broadcast call of the master 29
Bus access method 29
Bus status (C13211) 64
Bus termination 16
C
C01501 | Resp. to communication error with MCI 60
C01503 | MCI timeout 60
C13200 | Active address 61
C13202 | Slave address EPM value 61
C13204 | Override Slave Addresses 62
C13205 | Override of slave addresses during initialisation 62
C13206 | Slave profiles 62
C13207 | Response in case of communication fault 63
C13208 | AS-i: monitoring times 63
C13210 | AS-i bus transaction counter 63
C13211 | Bus status 64
C13213 | CTT2 block parameter transfer: Write parameter
block configuration 64
C13214 | CTT2 block parameter transfer: Read parameter block
configuration 65
C13220 | Display: Last data to master 65
C13221 | Display: Last data from master 66
C13852 | All words to standard device 66
C13853 | All words from standard device 66
C13900 | Firmware Product Type 67
C13901 | Firmware Compilation Date 67
C13902 | Firmware Version 67
C13950 | Module internal communication status 67
Cable length 16
Codes 60
Commissioning 24
Communication medium 16
Communication profile 16
Communication time 18
Communication-relevant parameters of the operating system
60
Configuring the master 25
Conformities 16
Connections 14
Conventions 7
Conventions used 7
CTT2
Acyclic device error codes 52
Block parameter transfer read mode 48
Block parameter transfer write mode 50
Read code 46
Read parameter value 44
Standard error codes 51
Write code 47
Write parameter value 45
CTT2 block parameter transfer
Read parameter block configuration (C13214) 65
Write parameter block configuration (C13213) 64
Cycle 31
Cycle time 16 , 31
Cyclic parameter data channel 17
D
Data transfer 29
Data transmission slave 1 (AS-i profile 7.A.5) 34
Data transmission slave 2 (AS-i profile 7.A.E) 36
Device and application-specific safety instructions 11
Device profiles 17 , 33
Device protection 11
Diagnostics 53
Diagnostics via parameter ports (parameter echo) 37
Diagnostics with the »Engineer« 54
Digital inputs, available 16
Display: Last data to master (C13220) 65
Document history 6
Drive offline (error message) 56
Drive parameter access failure - channel 1 (error message) 56
Drive parameter access failure - channel 2 (error message) 56
Drive PDO communication timeout (error message) 57
Index