Rockwell Automation GV3000/SE AC Drive Ver. 6.06 Hdwe Ref., Installation, and Troubleshooting Manual - Manual (Page 126)

Index-4 GV3000/SE AC Drive Hardware Reference, Version 6.06
fuse, 3-10
matching Power Module input to supplied
power, 3-5
NEMA enclosures, 2-2
output current, 2-2
power, 2-2
watts loss, 2-2
Reactors, 3-8
Regulator board
component locations, 2-12 to 2-14
description, 2-11
location, 2-4, 2-5, 2-6, 2-7, 2-8, 2-9, 2-10
part number, 9-12, 9-13, 9-14, 9-15, 9-16, 9-17
Relays, output status, see Status Relays
Reliance, getting assistance from, 1-1
Remote (digital input 8), 2-18, 7-2, 7-4, 7-5, 7-12
Remote Meter Interface board (RMI), 2-19, 2-20
Replacement parts, 9-12 to 9-17
Reset (digital input 3), 2-18, 7-2, 7-4, 7-5, 7-16
Reverse (digital input 6), 2-18, 7-2, 7-4, 7-5, 7-14
RMI, see Remote Meter Interface Board
RS-232
cable length, 3-9
communication port, 2-12 to 2-14, 2-18
terminal strip specifications, A-2
wiring, 2-18, 3-9, 7-1, 7-9
Run (digital input 4), 2-18, 7-2, 7-4, 7-5, 7-15
S
Sensorless vector control, 2-1
Serial communication,
see RS-232
Service conditions, A-1
Site requirements for drive installation, 3-1
Snubber resistor braking, 5-1
signal, 2-11
specifications, A-2
wiring, 2-17 to 2-18, 7-3, 7-4, 7-5, 7-16
Snubber Resistor Braking Kit, 2-20
Software, 1-1
Specifications
conduit opening sizes, 4-3 to 4-9
drive dimensions and weights, 3-2 to 3-3
encoder feedback device, A-3
environmental, 3-2
mounting hardware, 4-1
terminal strip inputs, A-2
terminal strip output, A-2
wire sizes, 3-5 to 3-7
Specifications, technical, A-1 to A-3
Speed, setting maximum, 7-7
Start (digital input 1), 2-18, 7-2, 7-4, 7-5, 7-16
Start enable see Function Loss
Status relays, Form A/B, 2-18, 7-3, 7-4, 7-5, 7-17
Stop (digital input 2), 2-18, 7-2, 7-4, 7-5, 7-16
Stopping the drive, 7-6
Super Remote Meter Interface board (RMI), 2-19,
2-20
SVC, see Sensorless Vector Control
T
Tachometer, pulse, see Encoder
Terminal strip
input specifications, A-2
output specifications, A-2
terminal identification, 2-17 to 2-18
tightening torque, 3-7
wiring, 2-18, 3-5 to 3-7, 7-1 to ??, 7-1 to 7-17
Thyristor precharge module, 2-9, 9-16
Transformer
current, 2-8, 2-9, 9-15, 9-16
ground fault, 2-8, 2-9, 2-10, 9-15, 9-16, 9-17
isolation input, installing, 5-1
Troubleshooting, 9-1 to 9-11
V
Vector regulation, 2-1
Ventilation,
see Air Flow
Volts/hertz regulation, 2-1
W
Watts loss rating, 2-2, 4-1
Weights, 3-2
Wire routing, 4-1 to 4-9
Wire size, 3-5 to 3-7
Wiring diagrams, 200-400 HP system, D-1