Document Outline

• Centellis 2000 Shelf - DC
• Contents
• About this Manual
  • Overview of Contents
  • Abbreviations
  • Conventions
  • Summary of Changes
• Safety Notes
  • EMC
  • System Installation
  • Blade and RTM Installation
  • Operation
  • System Expansion
  • Power Feed
  • PEMs
  • Fan Trays
  • Shelf Manager and Hub Board
  • Cabling
  • RJ-45 Connector
  • Laser
  • Environment
• Sicherheitshinweise
  • EMV
  • Systeminstallation
  • Board und RTM Installation
  • Betrieb
  • Systemerweiterung
  • Stromzufuhr
  • PEMs
  • Lüftermodule
  • Shelf-Manager-und-Hub-Board
  • Verkabelung/Kabelführung
  • RJ-45 Stecker
  • Laser
  • Umweltschutz
• System Overview
  • 1.1 Description
    • 1.1.1 Shelf
    • 1.1.2 Backplane
    • 1.1.3 Shelf Manager and Hub Board
    • 1.1.4 Node Slots
    • 1.1.5 Rear Transition Modules
    • 1.1.6 Power Inlet and Power Entry Modules
    • 1.1.7 Fan Trays
    • 1.1.8 Air Filters
    • 1.1.9 User Card Slots
  • 1.2 System Management
  • 1.3 Shelf Management
  • 1.4 Standard Compliances
  • 1.5 Ordering Information
• Site Preparation
  • 2.1 Overview
  • 2.2 Site Planning Considerations
    • 2.2.1 Receiving and Unpacking the System
    • 2.2.2 Site and Installation Planning
  • 2.3 Requirements
    • 2.3.1 Environmental Requirements
    • 2.3.2 Power Requirements
  • 2.4 Dimensions and Weight
  • 2.5 Mounting Options
  • 2.6 Cooling Considerations
  • 2.7 Acoustic Noise Control
• System Installation
  • 3.1 Overview
  • 3.2 Before Installation
    • 3.2.1 Type Label Location
    • 3.2.2 Requirements
    • 3.2.3 Tools You Will Need
  • 3.3 Installation
    • 3.3.1 Installing the System in a Rack
    • 3.3.2 Ground System/Bonding
    • 3.3.3 Powering-Up the System
  • 3.4 Removal
    • 3.4.1 Powering Down the System
    • 3.4.2 Disconnecting the System from Power Feed
    • 3.4.3 Removing the System
• FRU Installation
  • 4.1 Overview
  • 4.2 Installing and Removing RTMs and Blades
  • 4.3 Replacing the Shelf Manager and Hub Board
  • 4.4 Covering Unused Slots
  • 4.5 Replacing Power Entry Modules
  • 4.6 Replacing Fan Trays
  • 4.7 Maintaining Air Filters
    • 4.7.1 Replacing the Filters
    • 4.7.2 Storing the Filters
• Non-Field-Replaceable Units
  • 5.1 Overview
  • 5.2 Backplane
    • 5.2.1 Base Interface
    • 5.2.2 Fabric Interface
    • 5.2.3 Update Channel
    • 5.2.4 Synchronization Clock Interface
  • 5.3 Alarm Panel
  • 5.4 Power Inlet
• Cooling Subsystem
  • 6.1 Overview
  • 6.2 Cooling Subsystem
• Power Subsystem
  • 7.1 Overview
  • 7.2 Power Subsystem
    • 7.2.1 Power Supply
    • 7.2.2 Power Distribution
      • 7.2.2.1 Management Power Distribution
      • 7.2.2.2 High Power Distribution
      • 7.2.2.3 Power Interconnect
    • 7.2.3 PEM Specifications
      • 7.2.3.1 Power Input
      • 7.2.3.2 Power Filtering
• Network Management and System Access
  • 8.1 Overview
  • 8.2 Accessing System Components
  • 8.3 Network Management
    • 8.3.1 Slot Numbers and Slot Addresses
    • 8.3.2 Shelf Geographical Address
      • 8.3.2.1 Setting the Shelf Geographical Address
      • 8.3.2.2 Shelf Manager Replacement Scenarios
    • 8.3.3 IP Addresses
      • 8.3.3.1 Out-of-Band Interface
      • 8.3.3.2 Backplane Interfaces
      • 8.3.3.3 Configuration File
    • 8.3.4 Restoring Factory Settings
• DHCP Configuration and Network Boot
  • 9.1 Overview
  • 9.2 DHCP Configuration and Network Boot
    • 9.2.1 Preparing a TFTP Server for Network Boot and Installation
    • 9.2.2 Preparing a DHCP Server for Network Boot
• Redundancy
  • 10.1 Overview
  • 10.2 Redundancy
    • 10.2.1 Cold Standby
      • 10.2.1.1 Heartbeat
      • 10.2.1.2 Data Replication
      • 10.2.1.3 HPI Interface
    • 10.2.2 System Manager
    • 10.2.3 Redundancy Operations
      • 10.2.3.1 Shelf Manger Switchover
      • 10.2.3.2 Shelf Manager Takeover
      • 10.2.3.3 Shelf Manager Failover
      • 10.2.3.4 Shelf Manager Insertion
      • 10.2.3.5 Shelf Manager Extraction
• Software
  • 11.1 Overview
  • 11.2 Software Requirements
    • 11.2.1 Enclosed CDs
    • 11.2.2 BBS Installation
    • 11.2.3 Firmware Upgrade
  • 11.3 Blade Insertion and Extraction
    • 11.3.1 Power-On After Blade Insertion
    • 11.3.2 Power-Down Before Blade Extraction
• A Troubleshooting
  • A.1 Error List
    • A.1.1 Mechanical
    • A.1.2 After Power On
    • A.1.3 Fans
    • A.1.4 Shelf Managers
• B Technical Data
  • B.1 Acoustic Data
  • B.2 Airflow Data
    • B.2.1 Full Speed Operation
    • B.2.2 Single/Multiple Fan Failure
    • B.2.3 Fan Tray Replacement
    • B.2.4 Chassis Impedance
• C Related Documentation
  • C.1 Artesyn Embedded Technologies - Embedded Computing Documentation
  • C.2 Related Specifications