Verilink HDM 2180 (880-503048-001) Product Manual - Manual (Page 37)

Standalone HDM 2180 Management
Verilink HDM 2180 User Manual 3-13
Figure 3-8 Transmit Alarms Diagnostics Menu
Table 3-8 Transmit Alarms Diagnostics Menu Options
HDM > t HDM > t HDM > t HDM > t
--- TRANSMIT ALARMS DIAGNOSTICS MENU ---
--- TRANSMIT ALARMS DIAGNOSTICS MENU --- --- TRANSMIT ALARMS DIAGNOSTICS MENU --- --- TRANSMIT ALARMS DIAGNOSTICS MENU ---
Y) Transmit Yellow Alarm ................... off
Y) Transmit Yellow Alarm ................... off Y) Transmit Yellow Alarm ................... off Y) Transmit Yellow Alarm ................... off
A) Transmit AIS Alarm ...................... on
A) Transmit AIS Alarm ...................... on A) Transmit AIS Alarm ...................... on A) Transmit AIS Alarm ...................... on
S) Transmit IDLE Signal .................... off
S) Transmit IDLE Signal .................... off S) Transmit IDLE Signal .................... off S) Transmit IDLE Signal .................... off
F) Transmit FEBE ........................... off
F) Transmit FEBE ........................... off F) Transmit FEBE ........................... off F) Transmit FEBE ........................... off
E) Transmit FEAC DS3 EQUIPMENT FAILURE (SA). off
E) Transmit FEAC DS3 EQUIPMENT FAILURE (SA). off E) Transmit FEAC DS3 EQUIPMENT FAILURE (SA). off E) Transmit FEAC DS3 EQUIPMENT FAILURE (SA). off
L) Transmit FEAC DS3 LOS/HBER Alarm ........ on
L) Transmit FEAC DS3 LOS/HBER Alarm ........ on L) Transmit FEAC DS3 LOS/HBER Alarm ........ on L) Transmit FEAC DS3 LOS/HBER Alarm ........ on
O) Transmit FEAC DS3 Out-Of-Frame .......... off
O) Transmit FEAC DS3 Out-Of-Frame .......... off O) Transmit FEAC DS3 Out-Of-Frame .......... off O) Transmit FEAC DS3 Out-Of-Frame .......... off
R) Transmit FEAC DS3 AIS Received .......... off
R) Transmit FEAC DS3 AIS Received .......... off R) Transmit FEAC DS3 AIS Received .......... off R) Transmit FEAC DS3 AIS Received .......... off
I) Transmit FEAC DS3 Idle Received ......... off
I) Transmit FEAC DS3 Idle Received ......... off I) Transmit FEAC DS3 Idle Received ......... off I) Transmit FEAC DS3 Idle Received ......... off
C) Transmit FEAC DS3 Common Eqpt. Fail ..... off
C) Transmit FEAC DS3 Common Eqpt. Fail ..... off C) Transmit FEAC DS3 Common Eqpt. Fail ..... off C) Transmit FEAC DS3 Common Eqpt. Fail ..... off
P) Transmit FEAC DS3 EQUIPMENT FAILURE (NSA) off
P) Transmit FEAC DS3 EQUIPMENT FAILURE (NSA) off P) Transmit FEAC DS3 EQUIPMENT FAILURE (NSA) off P) Transmit FEAC DS3 EQUIPMENT FAILURE (NSA) off
X) exit menu
X) exit menu X) exit menu X) exit menu
HDM >
HDM > HDM > HDM >
Command Description
Y Transmit Yellow Alarm—Toggles transmission of RAI (Remote Alarm Indication signal) on
and off to enable or disable transmission of the far end receive failure in the outgoing
DS3 stream.
HDM > y
Perform Yellow Alarm(Y/N)? y
Enter choice(0 for Enable or 1 for Disable) >
A Transmit AIS Alarm—Toggles transmission of AIS (Alarm Indication Signal), a pattern of
unframed all ones, on and off to notify the other end that an alarm is being received.
HDM > a
Perform AIS Alarm(Y/N)? y
Enter choice(0 for Enable or 1 for Disable) >
S Transmit IDLE Signal—Toggles transmission of idle code on and off. The idle signal is
used for keeping the line active when no data signals are being sent.
HDM > s
Perform IDLE Signal Alarm(Y/N)? y
Enter choice(0 for Enable or 1 for Disable) >
F Transmit FEBE—Far-End Block Error—Toggles transmission of the Far End Block Error
alarm message on and off, controlling the insertion of Far End Block Errors in the
outgoing DS3 stream and emulating the alarm transmitted to the far end when a bit error
is received.
HDM > f
Perform FEBE Alarm(Y/N)? y
Enter choice(0 for Enable or 1 for Disable) >
E Transmit FEAC DS3 EQUIPMENT FAILURE (SA)—Conditions to cause activation of this
FEAC signal alarm are not defined for this module.
HDM > e
Perform Equipment FAIL SA Alarm(Y/N)? y
Enter choice(0 for Enable or 1 for Disable) >