Verilink HDM 2180 (880-503048-001) Product Manual - Manual (Page 52)

HDM 2180 Management: Using NCM 2000
4-6 Verilink HDM 2180 User Manual
Port
Configuration
Menu (DS3)
From the Configuration Menu, pressing P for the DS3 Port Set Up
option will display the Port Configuration Menu which is used for
setting the DS3 parameters. The line code is set at B3ZS and the
Alarm Indication Signal (AIS) C-bit is set for 0 (zero). These options
are used in the C-bit parity line type. Various alarm functions and
performance monitoring functions are not available with the M13
line type.
Figure 4-4 HDM 2180 Port Configuration Menu
Table 4-5 HDM 2180 Port Configuration Menu
Command Description Options
T Timing—Selecting this option will display the HDM 2180 Timing
Configuration Menu, which will in turn give the various options for the timing.
If the Synchronization option is selected, you will be presented with the three
options listed below.
[0.0.0.9] [1,5] HDM 2180 > t
-- HDM 2180 Timing Configuration Menu --
Source Synchronization Auto Restore
PRIMARY S) Recover Clock -- YES
X) Exit this screen
[0.0.0.9] [1,5] HDM 2180 > s
Select Timing:
1) RECOVER 2) EXTERNAL T3 3) INTERNAL CLK
1) Recover
2) External T3
3) Internal Clk
B Line Build Out—Toggles between normal cable (less than 250 feet) and long
cable (greater than 250 feet). The selection reflects the distance to an optical
fiber multiplexer or T3 repeater on the network side.
1) Normal cable
2) Long cable
R Performance Control—Toggles performance control On and Off, use of the C-
bit channel for control of a far-end unit.
1) On
2) Off
-- HDM 2180 Port Configuration Menu -- -- HDM 2180 Port Configuration Menu -- -- HDM 2180 Port Configuration Menu -- -- HDM 2180 Port Configuration Menu --
- Line Type C-Bit Parity
- Line Type C-Bit Parity - Line Type C-Bit Parity - Line Type C-Bit Parity
- Line Code B3ZS
- Line Code B3ZS - Line Code B3ZS - Line Code B3ZS
- AIS C-Bit 0
- AIS C-Bit 0 - AIS C-Bit 0 - AIS C-Bit 0
T) Timing Internal Clk
T) Timing Internal Clk T) Timing Internal Clk T) Timing Internal Clk
B) Line Build Out Normal Cable
B) Line Build Out Normal Cable B) Line Build Out Normal Cable B) Line Build Out Normal Cable
R) Performance Control On
R) Performance Control On R) Performance Control On R) Performance Control On
M) Data Rate Mode Only NE
M) Data Rate Mode Only NE M) Data Rate Mode Only NE M) Data Rate Mode Only NE
D) Data Rate 28, (44.7 Mbps)
D) Data Rate 28, (44.7 Mbps) D) Data Rate 28, (44.7 Mbps) D) Data Rate 28, (44.7 Mbps)
E) Equipment ID equipID
E) Equipment ID equipID E) Equipment ID equipID E) Equipment ID equipID
L) Location ID locID
L) Location ID locID L) Location ID locID L) Location ID locID
F) Frame ID frameID
F) Frame ID frameID F) Frame ID frameID F) Frame ID frameID
U) Unit ID unitID
U) Unit ID unitID U) Unit ID unitID U) Unit ID unitID
A) Facility ID facilityID
A) Facility ID facilityID A) Facility ID facilityID A) Facility ID facilityID
P) Port ID portID
P) Port ID portID P) Port ID portID P) Port ID portID
C) Circuit ID circuitID
C) Circuit ID circuitID C) Circuit ID circuitID C) Circuit ID circuitID
G) Test Sig ID 9
G) Test Sig ID 9 G) Test Sig ID 9 G) Test Sig ID 9
I) Inband Control Disable
I) Inband Control Disable I) Inband Control Disable I) Inband Control Disable
X) Exit this screen
X) Exit this screen X) Exit this screen X) Exit this screen
[127.255.255.0] [1,6] HDM 2180 >
[127.255.255.0] [1,6] HDM 2180 > [127.255.255.0] [1,6] HDM 2180 > [127.255.255.0] [1,6] HDM 2180 >