Yaskawa F7 to A1000 - Manual (Page 49)

10 Appendix 2 Parameter Cross Reference
YASKAWA PL.A1000.02 F7 to A1000 - Product Transition Guide 49
MEMOBUS
Communication
Drive Node
Address
H5-01 1F H5-01 1F —
Communication
Speed Selection
H5-02 3 H5-02 3
H5-02 H5-02
0: 1200 bps 0: 1200 bps
1: 2400 bps 1: 2400 bps
2: 4800 bps 2: 4800 bps
3: 9600 bps 3: 9600 bps
4: 19200 bps 4: 19200 bps
— 5: 38400 bps
— 6: 57600 bps
— 7: 76800 bps
— 8: 115200 bps
Communication
Parity Selection
H5-03 0 H5-03 0
H5-03 H5-03
0: No parity 0: No parity
1: Even parity 1: Even parity
2: Odd parity 2: Odd parity
Stopping Method
After
Communication
Error
H5-04 3 H5-04 0
H5-04 H5-04
0: Ramp to stop 0: Ramp to stop
1: Coast to stop 1: Coast to stop
2: Fast Stop 2: Fast Stop
3: Alarm Only 3: Alarm Only
Communication
Fault Detection
Selection
H5-05 1 H5-05 0
H5-05 H5-05
0: Disabled 0: Disabled
1: Enabled 1: Enabled
Drive Transmit
Wait Time
H5-06 5 ms H5-06 5 ms —
RTS Control
Selection
H5-07 1 H5-07 1
H5-07 H5-07
0: Disabled
(RTS always on) 0: Disabled
(RTS always on)
1: Enabled
(RTS enabled during send
only)
1: Enabled
(RTS enabled during send only)
Unit Selection for
MEMOBUS
Register 0025H
H5-10 0 H5-10 0
H5-10 H5-10
0: 0.1 V units 0: 0.1 V units
1: 1 V units 1: 1 V units
Pulse Train I/O
Pulse Train Input
Function Selection
H6-01 0 H6-01 0
H6-01 H6-01
0: Frequency reference 0: Frequency reference
1: PID feedback value 1: PID feedback value
2: PID setpoint value 2: PID setpoint value
— 3: V/f Control with Simple PG feedback
Pulse Train I/O
Pulse Train Input
Scaling
H6-02 1440 Hz H6-02 1440 Hz —
Pulse Train Input
Gain
H6-03 100.0 % H6-03 100.0 % —
Pulse Train Input
Bias
H6-04 0.0 % H6-04 0.0 % —
Pulse Train Input
Filter Time
H6-05 0.10 s H6-05 0.10 s —
Pulse Train
Monitor Selection
H6-06 2 H6-06 102
H6-06 H6-06
01: Frequency reference 101: Frequency reference
02: Output frequency 102: Output frequency
05: Motor speed 105: Motor speed
20: Output frequency after
soft start
116: Output frequency after soft start
24: PID feedback 501: PID feedback
36: PID input amount 502: PID input amount
Pulse Train
Monitor Scaling
H6-07 1440 Hz H6-07 1440 Hz —
Parameter Name
F7 A1000 Setting
Parameter Default Parameter Default F7 A1000