Seiko FB-900 - Manual (Page 179)

ESC ( - (27,40,45)D (1B,28,2D)H Specifies line type. ( n1 = 3 ) ( n2 = 0 ) ( m = 1 )
n1 n2 n1 n2 n1 n2 d1 = 1 Underscore d2 = 1 Single line
m m m d1 = 2 Center line d2 = 2 Double lines
d1 d2 d1 d2 d1 d2 d1 = 3 Upper line d2 = 5 Single dotted line
d2 = 6 Double dotted lines
d2 = 0 Cancels the line specification.
ESC ( ^ (27,40,94)D (1B,28,5E)H All-character set.
n1 n2 n1 n2 n1 n2 Prints n1 + n2 x 256 characters in the all-character character set.
ESC ( t (27,40,116)D (1B,28,74)H Specifies a character set.
n1n2 n1 n2 n1 n2 d1 : Displays ESC t n command table No.
d1 d2 d1 d2 d1 d2 d2, d3 : Specifies the character set.
d3 d3 d3 d2 = 0, d3=0 : ITALIC
d2 = 1, d3=0 : PC-437
d2 = 3, d3=0 : PC-850
d2 = 7, d3=0 : PC-860
d2 = 8, d3=0 : PC-863
d2 = 9, d3=0 : PC-865
d2 = 11, d3=0 : PC-857
d2 = 44, d3=0 : PC-858
d2 = 24, d3=0 : PC-861
d2 = 25, d3=0 : PC-BRASCII
d2 = 26, d3=0 : PC-ABICOMP
d2 = 17, d3=0 : ISO-8859-1
ESC + (27)D(43)D (1B)H (2B)H Specifies a line feed pitch of n/360 inch. (0
≤
n
≤
255)
n n n
ESC - (27)D(45)D (1B)H (2D)H Specifies or cancels underscoring.
n n n n = 01, 31: Specifies underscoring.
n = 00, 30 : Cancels underscoring.
ESC / (27)D(47)D (1B)H (2F)H Selects the vertical tab channel. (0
≤
n
≤
7)
m m m
ESC 0 (27)D(48)D (1B)H (30)H Specifies 1/8 inch line feed pitch.
ESC 2 (27)D(50)D (1B)H (32)H Specifies 1/6 inch line feed pitch.
ESC 3 (27)D(51)D (1B)H (33)H Specifies line feed pitch of n/180 inch. (0
≤
n
≤
255)
n n n
ESC 4 (27)D(52)D (1B)H (34)H Specifies the italic font.
ESC 5 (27)D(53)D (1B)H (35)H Cancels the italic font.
ESC 6 (27)D(54)D (1B)H (36)H Expands the character code area.
Makes the area from
(80)H to (9F)H the character code area,
rather than the control code area, when the graphic character
table or down-load character table is selected. This is the initial
condition.
ESC 7 (27)D(55)D (1B)H (37)H Cancels the expanded character code area.
ESC : (27)D(58)D (1B)H (3A)H Copies the internal character set. (0
≤
n
≤
255)
NUL NUL NUL Draft mode: n = 0
n s n s n s LQ mode: n = 0 ~ 9
s : Down-load character set number (See ESC & )
ESC < (27)D(60)D (1B)H (3C)H Returns to the home position.
Move the print head to the left end without sensing the home
position.
● EPSON Software commands
Decimal Hex
Symbol Function
Code
8-3 — 8. Software commands —