Seiko FB-900 - Manual (Page 188)

— 8. Software commands —
ESC N (27)D(78)D (1B)H (4E)H Specifies the bottom margin. (1
≤
n
≤
255)
n n n The number of lines to be skipped is specified by “n” and the
bottom margin is specified in the preset line feed amount.
ESC O (27)D(79)D (1B)H (4F)H Cancels the bottom margin.
ESC P (27)D(80)D (1B)H (50)H Specifies or cancels proportional printing.
n n n n = 0 : Cancels proportional printing.
n = 1 : Specifies proportional printing.
This command is valid when #34 PITCH LOCK is set to NO.
ESC Q (27)D(81)D (1B)H (51)H Printer deselect
n n n Brings the printer into the deselect state when n=(23)H,(B9)H.
Valid when #71 SELECT IN ENABLE is set to 1 in the
EXTENDED SETUP MODE or set to
I/F and the SELECT IN
signal is high.
ESC R (27)D(82)D (1B)H (52)H Initializes the horizontal and vertical tab positions.
Clears the vertical tab position.
ESC S (27)D(83)D (1B)H (53)H Specifies superscript or subscript.
n n n n = 0 : Specifies superscript.
n = 1 : Specifies subscript.
ESC T (27)D(84)D (1B)H (54)H Cancels superscript or subscript.
ESC U (27)D(85)D (1B)H (55)H Specifies or cancels uni-directional printing.
n n n n = 0 : Cancels uni-directional printing.
n = 1 : Specifies uni-directional printing.
ESC W (27)D(87)D (1B)H (57)H Specifies or cancels double-width printing.
n n n n = 0 : Cancels double-width printing.
n = 1 : Specifies double-width printing.
ESC X (27)D(88)D (1B)H (58)H Specifies the right and left margins. {0
≤
n
≤
255} {0
≤
m
≤
255}
n m n m n m
ESC Y (27)D(89)D (1B)H (59)H Specifies the 8-dot double-speed double-density graphic mode.
n1 n2 n1 n2 n1 n2 Number of data k = n1 + n2
×
256
d1 d2 d1 d2 d1 d2 Horizontal dot density : 120 dpi
••• dk ••• dk ••• dk Maximum dots per line : 1632 dot
Horizontally adjacent dots cannot be printed.
ESC Z (27)D(90)D (1B)H (5A)H Specifies the quadruple-density graphic mode.
n1 n2 n1 n2 n1 n2 Number of data k = n1 + n2
×
256
d1 d2 d1 d2 d1 d2 Horizontal dot density : 240 dpi
••• dk ••• dk ••• dk Maximum dots per line : 3264 dot
Horizontally adjacent dots cannot be printed.
ESC [ - (27,91,45)D (1B, 5B, 2D)H Specifies the line type.
n1 n2 n1 n2 n1 n2 Number of data k = n1 + n2
×
256
m1 m2 m1 m2 m1 m2 m1 = 1 : Underscore m2 = 0 : Cancels the line specification.
m1 = 2 : Center line m2 = 1 : Single line
m1 = 3 : Upper line m2 = 2 : Double lines
m2 = 255 : Cancels the line specification.
● IBM Software commands
Decimal Hex
Symbol Function
Code
8-12