Pioneer SVM-1000 - Manual (Page 18)

USING THE EFFECT FUNCTION
18
En
1 Touch the [BPM AUTO/TAP] button to select the BPM (=Beat
Per Minute) measurement mode.
AUTO: The BPM is automatically measured from the input
music signal.
TAP: Tap the TAP button with your finger to manually input the
BPM.
• Whenever power is first turned ON, [ AUTO] is selected by
default.
• The selected mode ([ AUTO]/[TAP]) will appear in the
display.
• When a BPM cannot be measured automatically, the BPM
display in the display will flash.
• The measurement range of AUTO mode is BPM=70 to 180.
Depending on the track, the BPM may not be accurately
measured. In these cases, use TAP mode to manually enter
the BPM.
[Manually entering the BPM using the TAP button]
When the TAP button is tapped to the beat (a quarter note) more
than twice, the average length will be set as the BPM.
• Pressing the TAP button during [AUTO] mode will switch the
BPM measurement mode to [ TAP], and the length between the
taps will be measured.
• When a BPM is set using the TAP button, the multiplication
factor will become [ 1/1] or [4/1] (depending on the effect), and
the effect time will be set to either the length of 1 beat (a quarter
note) or 4 beats.
• Rotate the TIME/PARAMETER dial while pressing the TAP
button to set the BPM directly.
2 Touch the effect category button [BEAT].
• The [
BEAT] button will be highlighted and an animation will
appear.
• The BEAT effect screen will be displayed.
• Whenever power is first turned ON, the [
BEAT] effect is
selected by default.
3 Use the effect select buttons to select an effect type.
• The selected button will be highlighted and an animation
will appear.
• For a description of each effect, refer to P. 23.
4 Use the CH SELECT dial to select the channel to which you
wish to apply the effect.
• The selected effect channel display will be highlighted.
• If [
MIC] is selected, the audio effect will be applied to both
MIC 1 and MIC 2. There will be no effect on the video.
• When turning the power ON, [ MASTER] will be selected.
5 Touch the effect mode select button to select the effect
mode.
• The selected button will be highlighted and an animation
will appear.
A: The effect will be applied to the audio only.
AV: The effect will be applied to both the audio and video.
V: The effect will be applied to the video only.
• When turning the power ON, [
AV] will be selected.
6 Touch the beat button to choose the multiplication factor of
the beat for synchronization of the effect.
• Select the beat number calculated from the BPM.
• The selected beat button will be highlighted.
• An effect time that corresponds to the multiplication factor
of the beat will be automatically set.
[Example] When BPM=120
1/1 = 500 ms
1/2 = 250 ms
2/1 = 1000 ms
7 Set the EFFECT ON/OFF button to ON to apply the effect.
• Each time the button is pressed it will switch between ON
and OFF (whenever power is first turned ON, the setting
defaults to OFF).
• When effect is ON, the button flashes.
Character
Rotate the
VIDEO FX PATTERN/TEXT BANK dial to select a video
character for the selected video effect.
For descriptions on the video character change caused by rotating
the
VIDEO FX PATTERN/TEXT BANK dial, refer to P. 24.
Parameter 1
Rotate the
TIME/PARAMETER dial to adjust temporal parameters
of the selected effect.
For descriptions on the changes in parameter 1 caused by turning
the
TIME/PARAMETER dial, refer to P. 23.
Parameter 2
Rotate the
LEVEL/DEPTH dial to adjust quantitative parameters of
the selected effect.
For descriptions on the changes in parameter 2 caused by rotating
the
LEVEL/DEPTH dial, refer to P. 23.
VISUALIZER MODE
A video is created internally, and effects can be applied to it.
This is effective when no input video is present.
01_SVM-1000_En.book 18 ページ ２００７年１０月１６日 火曜日 午前９時２２分