Alpha Technologies XM3-HP Series - Technical Manual - Manual (Page 64)

64 017-882-B0-001 Rev. C2 (10/2013)
3.0
Operation
3.3.2 Battery Information and Configuration
The top line of the display is affected by pressing a softkey. In this case, pressing Enter <ENTR>
will open the BATTERY INFO/BATTERYCONFIG Menu enabling the operator to set values for the
following parameters.
BATTERY INFO MENU
NOTE
BATT CONFIG <ENTR> Pressing enter goes to the Battery Configuration menu shown below
BATT VOLTS
Displays combined string voltage
CHARGER CURR Displays Batt Current for Inverter Mode
CHARGER MODE Displays current Charger Mode: OFF/FLOAT/REFRESH
IND BATT V Not displayed if no DSM3 or SAG installed
BATT TEMP Displays battery temperatures (°C)
APPS INFO <ENTR> Pressing enter goes to the APPS/INFO menu on APPS Tab*
SAG INFO <ENTR> Pressing enter goes to the SAG INFO menu shown at right
BATTERY CONFIG MENU
Default Range Note
BATT MHOS 0 0-2550
Hidden if no APPS card is installed
BATT DATES User programmable
BATT MODEL OTHER AlphaCell models listed at right
BATT STR DETECT AUTO AUTO / MANUAL
NUM BATT STRINGS 1 1-4
BATT CAPACITY 100AH 0*, 1–1000
Automatically set when AlphaCell model is selected.
FLOAT 2.27V/C 2.10-2.35
ACCEPT 2.40V/C 2.20-2.45
REFRESH 2.45V/C 2.40-2.50
REST ENABLE OFF ON/OFF
TEMP COMP 5.0MV 0-5.0MV per cell
EOD TYPE STRING IND or STRING
Individual Battery EOD only if sense harness is connected
Will display STR OVER for STRING override mode
EOD VOLT 1.75V/C Hidden if EOD TYPE = STRING
REFESH ENABLE ON ON/OFF Pressing Enter goes to adjust screen
SAG OPTION
AUTO
Auto-recognize Smart AlphaGuard (SAG)
SAG FW V1.00.0 Hidden if no SAG connected
SAG ##### Hidden if no SAG connected
HEATER MAT NO YES/NO Pressing Enter goes to adjust screen
AlphaCell Batteries
4.0HP
3.5HP
220GOLD
220HPL
220GXL
210GXL
195GXL
195GOLD
180GXL
165GXL
115HPL
85GXL
70HPL
OTHER
170XLT
XM3-918-HP 90V/0.4A
OPERATION NORMAL
OK
PWR
OK
BATT
OK
COMM
OK
APPS
Individual Battery
Volts Menu
BATT A1 VOLTS*
BATT A2 VOLTS*
BATT A3 VOLTS*
BATT B1 VOLTS*
BATT B2 VOLTS*
BATT B3 VOLTS*
BATT C1 VOLTS*
BATT C2 VOLTS*
BATT C3 VOLTS*
BATT D1 VOLTS*
BATT D2 VOLTS*
BATT D3 VOLTS*
NO BATTERIES**
3.3 Smart Display Menus, continued
3.0 Operation, continued
SAG INFO
BALANCING STR*
DUR REMAIN ###### M**
A MAX DELTA #### mV**
B MAX DELTA #### mV**
C MAX DELTA #### mV**
D MAX DELTA #### mV**
A BAL STAGE MODERATE**
B BAL STAGE MODERATE**
C BAL STAGE MODERATE**
D BAL STAGE MODERATE**
A SEVERE DUR ##### M**
B SEVERE DUR ##### M**
C SEVERE DUR ##### M**
D SEVERE DUR ##### M**
BALANCER DIS YES/NO
POWERSAVE MODE YES/NO
NUM OF STRINGS ##
SAG HARDWARE ID
* Displays NONE if no strings
are being balanced
** Displays only if string is
present
* Displays only if
battery is present
** Displays if no
batteries are
present
* Displays only if Apps Card is installed
* BATT CAPACITY should only be set to "0" when no batteries are present to disable NO BATT Alarm.