Sony ECM-X7BMP Electret Condenser Lavalier Microphone for UWP Transmitters - Manual (Page 6)

Precaution
6
Precaution
On Safety
 Operate the unit only with a power source as specified
in the “Specifications” section.
 A nameplate indicating operating voltage, etc., is
located on the rear panel.
 Should any solid object or liquid fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it any further.
 Do not drop or place heavy objects on the power cord.
If the power cord is damaged, turn off the power
immediately. It is dangerous to use the unit with a
damaged power cord.
 Unplug the unit from the wall outlet if it is not to be
used for several days or more.
 Disconnect the power cord from the AC outlet by
grasping the plug, not by pulling the cord.
 The socket-outlet shall be installed near the
equipment and shall be easily accessible.
On Installation
 Allow adequate air circulation to prevent internal heat
build-up.
Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation holes.
 Do not install the unit in a location near heat sources
such as radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical vibration or
shock.
BVM-E251
When installing the installation space must be secured
in consideration of the ventilation and service operation.
 Do not block the ventilation slots, and vents of the
fans.
 Leave a space around the unit for ventilation.
 Leave more than 40 cm of space in the rear of the unit
to secure the operation area.
When the unit is installed on the desk or the like, leave at
least 1U (4.4 cm) of space above and below the unit.
Leaving more than 40 cm of space above the unit is
recommended in consideration of service operation.
BVM-E171
When the unit is installed in a rack, leave at least 1U (4.4
cm) of space above and below, 1.0 cm of space left and
right between the rack and the unit.
Transportation of the Unit
Do not subject the unit to severe vibration or high
impact conditions during transportation. Doing so may
result in deformation of the internal structure or exterior
of the unit, damage of the screen, malfunction of the
internal parts, or other damage.
Make sure not to expose the unit to strong vibration or
high impact when you transport the unit as cargo by
truck, ship, or air, or as luggage with a rolling luggage
bag.
Avoid transporting or carrying the unit with the display
facing up or down.
Also, pack the unit in the protective bag provided to
prevent dust from entering the unit.
Connecting to Other Devices
When connecting this unit to other devices, turn off this
unit and the other devices beforehand. Connecting
while turned on may cause a malfunction to this unit
and the other devices.
Handling the Screen
 The OLED panel fitted to this unit is manufactured
with high precision technology, giving a functioning
pixel ratio of at least 99.99%. Thus a very small
proportion of pixels may be “stuck”, either always off
(black), always on (red, green, or blue), or flashing. In
addition, over a long period of use, because of the
physical characteristics of the organic light-emitting
diode, such “stuck” pixels may appear spontaneously.
These problems are not a malfunction.
 Do not leave the screen facing the sun as it can damage
the screen. Take care when you place the unit by a
window.
 Do not push or scratch the monitor’s screen. Do not
place a heavy object on the monitor’s screen. This may
cause the screen to lose uniformity.
 The screen and the cabinet become warm during
operation. This is not a malfunction.
On High Brightness Display
 Using the unit with the high brightness display for
extended periods may cause eyestrain or reduction of
eyesight. Be sure to take an occasional break when
using.
 Follow RECOMMENDATION ITU-R BT.1702
“Guidance for the reduction of photosensitive
epileptic seizures caused by television” or other
guidelines when using.