Yokogawa ADMAG AXF - Manual (Page 109)

IM 01E20C01-01E 11-8
11. OUTLINE
● Remote Converter AXFA11G /RK (AM11 Replacement Bracket)
Pipe mounting
133.5(5.26) 180(7.09)
194(7.64)
210(8.27)
(80.5) (3.17)
49
(1.93)
29 (1.14)
24 (0.94)
65(2.56)
(80.5)
(3.17)
31
(1.22)
31
(1.22)
31
(1.22)
31
(1.22)
FF0AXFA11E.EPS
Bracket for replacement
(For pipe mounting)
4-ø6(0.24)
(Surface mounting hole)
(190)
(7.48)
Bracket for replacement
(For surface mounting)
(62)
(2.44)
18(0.71) Mouting Screw
*1
Surface mounting
(126.5) (4.98)
*1: These screws must be
* provided by the user.
● Unless otherwise specified, difference in the dimensions are refer to the following table.
Above Equal or below Above Equal or below
Category of basic dimension Category of basic dimension
Tolerance Tolerance
3 (0.12)
6 (0.24)
10 (0.39)
18 (0.71)
30 (1.18)
50 (1.97)
80 (3.15)
120 (4.72)
180 (7.09)
250 (9.84)
315 (12.40)
400 (15.75)
3 (0.12)
6 (0.24)
10 (0.39)
18 (0.71)
30 (1.18)
50 (1.97)
80 (3.15)
120 (4.72)
180 (7.09)
250 (9.84)
315 (12.40)
400 (15.75)
500 (19.69)
Ϯ0.7 (Ϯ0.03)
Ϯ0.9 (Ϯ0.04)
Ϯ1.1 (Ϯ0.04)
Ϯ1.35 (Ϯ0.05)
Ϯ1.65 (Ϯ0.06)
Ϯ1.95 (Ϯ0.08)
Ϯ2.3 (Ϯ0.09)
Ϯ2.7 (Ϯ0.11)
Ϯ3.15 (Ϯ0.12)
Ϯ3.6 (Ϯ0.14)
Ϯ4.05 (Ϯ0.16)
Ϯ4.45 (Ϯ0.18)
Ϯ4.85 (Ϯ0.19)
500 (19.69)
630 (24.80)
800 (31.50)
1000 (39.37)
1250 (49.21)
1600 (62.99)
2000 (78.74)
2500 (98.43)
630 (24.80)
800 (31.50)
1000 (39.37)
1250 (49.21)
1600 (62.99)
2000 (78.74)
2500 (98.43)
3150 (124.02)
Ϯ5.5 (Ϯ2.17)
Ϯ6.25 (Ϯ0.25)
Ϯ7.0 (Ϯ0.28)
Ϯ8.25 (Ϯ0.32)
Ϯ9.75 (Ϯ0.38)
Ϯ11.5 (Ϯ0.45)
Ϯ14.0 (Ϯ0.55)
Ϯ16.5 (Ϯ0.65)
Remarks: The numeric is based on criteria of tolerance class IT18 in JIS B 0401.
General tolerance in the dimensional outline drawing.
Unit : mm (approx.inch)