Yokogawa EJX430B - Manual (Page 100)

<11. General Specifications>
11-9
IM 01C27B01-01EN
 OPTIONAL SPECIFICATIONS
Item Description Code
Painting
Color change Amplifier cover only P
Coating
change
Anti-corrosion coating *1 X2
Oil-prohibited use *2
Degrease cleansing treatment K1
Degrease cleansing treatment and with fluorinated oilfilled capsule.
Operating temperature -20 to 80°C ( -4 to 176°F)
K2
Oil-prohibited use
with dehydrating treatment *2
Degrease cleansing treatment and dehydrating treatment K5
Degrease cleansing treatment and dehydrating treatment with fluorinated oilfilled
capsule.
Operating temperature -20 to 80°C ( -4 to 176°F)
K6
Capsule fill fluid
Fluorinated oil filled in capsule
Operating temperature -20 to 80°C ( -4 to 176°F)
K3
Calibration units *3
P calibration (psi unit)
(See Table for Span and Range Limits.)
D1
bar calibration (bar unit) D3
M calibration (kgf/cm 2 unit) D4
Long vent *4
Total length: 119 mm (standard: 34 mm); Total length when combining with option
code K1, K2, K5, and K6: 130 mm. Material: 316 SST
U1
Gold-plated capsule gasket *5 Gold-plated 316L SST capsule gasket. Without drain and vent plugs. GS
Gold-plated diaphragm* 6
Inside of isolating diaphragms (fill fluid side) are gold plated, effective for hydrogen
permeation.
A1
130 Pa abs calibration* 7 Minimum input puressure at calibration testing: 130 Pa abs (1 mmHg abs) S1
Body option *8
Without drain and vent plugs. N1
N1 and Process connection, based on IEC61518 with female thread on both sides
of cover flange, with blind kidney flanges on back.
N2
N2 and Material certificate for cover flange, diaphragm, capsule body, and blind
kidney flange.
N3
European Pressure
Directive *9
PED 97/23/EC
Category III, Module H, Type of Equipment: Pressure Accessory-Vessel,
Type of Fluid: Liquid and Gas, Group of Fluid: 1 and 2.
PE3
Material certificate *10
Cover flange *11 M01
Cover flange, Process connector *12 M11
Pressure test/
Leak test certificate
Test Pressure: 16 MPa (2300 psi)* 13
Nitrogen(N
2
) Gas *18
Retention time: one minute
T12
Test Pressure: 25 MPa (3600 psi)* 14 T13
Test Pressure: 3.5 MPa (500 psi)* 15 T01
Test Pressure: 500 kPa (2000 inH
2
O)* 16 T11
Test Pressure: 50 kPa (200 inH
2
O)* 17 T04
*1: Not applicable with color change option.
*2: Applicable for Wetted parts material code S, H, M, and T.
*3: The unit of MWP (Max. working pressure) on the name plate of the housing is the same unit as specified by Option code D1, D3,
and D4.
*4: Applicable for vertical impulse piping type (Installation code 7) and Wetted parts material code S, H, M, and T.
*5: Applicable for wetted parts material code S; process connection code 0 and 5; and installation code 8 and 9. Not applicable for
option code U1, N2, N3 and M11. No PTFE is used for wetted parts.
*6: Applicable for wetted parts material code S.
Overpressure effects for EJX110B M, H, and V capsules: ±0.06% of URL.
*7: Applicable only for EJX310B M and A capsules whose upper range value is set as smaller than 53.3 kPa abs.
*8: Applicable for Wetted parts material code S, H, M, and T; Process connection code 3, 4, and 5; Installation code 9; and Mounting
bracket code N. Process connection faces on the other side of zero adjustment screw.
*9: Applicable for M, H and V capsules of EJX110B with wetted parts material code S.
*10: Material traceability certification, per EN 10204 3.1B.
*11: Applicable for Process connections code 0 and 5.
*12: Applicable for Process connections code 1, 2, 3, and 4.
*13: Applicable for Capsule code L of EJX110B, Capsule code B of EJX430B and EJX310B, and all the capsules of EJX110B with
wetted parts maerial code H, M, T, A, D, and B.
*14: Applicable for Capsule code M, H, and V of EJX110B with wetted parts material code S.
*15: Applicable for Capsule code A of EJX430B and EJX310B.
*16: Applicable for Capsule code H of EJX430B.
*17: Applicable for Capsule code L and M of EJX310B.
*18: Pure nitrogen gas is used for oil-prohibited use (Option code K1, K2, K5, and K6).