TeeJet Matrix Pro 840G User Manual - Manual (Page 13)

6
www.teejet.com
HOME
OVER
VIE
W
SE
TUP
POWER
APPENDIX
FULL SCREEN
INTR
ODUC
TION
GUID
ANCE
CONFiGURATiONS
The following diagrams are reflective of typical Matrix Pro configurations. Due to the variety of possible configurations, these should be used
for reference purposes only.
Figure 1-6: Matrix Pro w/RealView Camera
16-00022: RealView Camera
Co
nn e ct to
+1
2v
On
ly
Powe
rC
ab le
45-05645
Power
Cable, 12V
45-05775
10'/3m Power
Cable, Battery
CAUTION CONN. TO +12V ONLY
PO W ER CABLE 45 -05775 DC:
XX
XX
8 Pos.
45-05617: 20'/6m
45-05618: 60'/18m
Camera Extension Cable
45-05765
Speed/Sense Cable
5 Pos.
32-50008 Switch
Matrix Pro 570G
75-30082
75-30083 w/GLONASS
Matrix Pro 840G
75-30084
75-30090 w/GLONASS
GPS Antenna
78-50155
78-50190 w/GLONASS
Kit, RAM Mount w/Suction Cup
90-02349 (Matrix 570G)
90-02700 (Matrix 840G)
8 Pos.
Speed Cable
Camera
+12V
Matrix
FieldPilot
BoomPilot
Optional Accessory
Speed Out / Sense In Cable
The Speed Out / Sense In Cable assists the Matrix Pro with two
additional connections that:
►Send a radar speed signal to an external device
►Allow the user to operate the area applied function of the Matrix
Pro in series with a remote master connection or existing apply
on/off toggle in a single swath manner. However, if the previous
connections are not available, the supplied toggle switch will allow
area applied functionality without the need to connect to a functional
application implement.
Connecting to different consoles requires different adapters and
calibrations.
• If connecting to TeeJet consoles, please use speed adapter
45-20042
◄enter calibration # 914 (#1000 in Europe) for 8xx series in
RAD mode
◄enter calibration # 9140 (#10000 in Europe) for below LH 70
Series, LH 85, 500 series, 5000, 6000, IC 18, IC 24 and IC 34
• If connecting to Mid-Tech consoles no adapter is required
◄enter calibration # 1000
• If connecting to Raven consoles use speed adapter 45-05508
(do not connect the 12v red wire from 45-05508)
◄enter calibration # 800
Speed Out / Sense In Cable Is Required To Start
Application Mapping.
The Speed Out / Sense In Cable allows the user to operate the area
applied function of the Matrix Pro in series with a remote master
connection or existing apply on/off toggle in a single swath manner.
However, if the previous connections are not available, the supplied
toggle switch will allow area applied functionality without the need to
connect to a functional application implement.
The cable also sends a radar speed signal to an external device.
To install your cable:
• Connect using included switch (32-50008)
OR
• Connect green wire to master 12 Volts on/off from rate controller,
foot switch or implement status switch
If sensing boom shut-off for applied mapping from an existing
console, attach the green wire to the valve side of the master switch
on the console. The red wire is not used.
Figure 1-7: Speed Out / Sense In cable
Speed Cable
45-05615
Speed/
Status
+12v
Connect Green Wire
Connect Red Wire
OFF
ON
Green Wire Sense
Red Wire (+12v)
32-50008 Switch, Master
Radar
Speed
Out
45-05765
Speed/Sense Cable