American Time SiteSync IQ - Manual (Page 52)

© American Time
52
SiteSync IQ Installation Manual
Wireless Analog Clock Installation
Wireless Analog AC Clocks
Wireless Analog AA Battery Clocks (DC)
n Note: SiteSync IQ clocks ship with batteries installed. Do not connect the barrel
jack plug to the receiver until the master is installed and transmitting.
u
Connect the barrel jack plug of the battery pack to the wireless receiver.
v
The LED on the back of the clock will turn red for 1 second then briefly
flash orange (1-15 flashes) indicating the receive frequency on power up.
Within 30 seconds of power up the LED will flash red or green. Red
indicates the receiver is looking for the signal and green indicates the
signal has been received. When the movement starts to correct, the LED
will turn off.
n Note: If the LED does not flash within 30 seconds, remove barrel jack plug
of the battery pack from the receiver, wait for 5 seconds and reconnect it. The LED
should begin flashing within 30 seconds.
w
Within 3-5 minutes after activation, the green LED will stop flashing and
the clock hands should rapid advance to the correct time. If clocks do not
synchronize within 10 minutes of battery activation, see n Note in
step 2.
x
Hang the clock using the keyhole hanger on the back of the clock or the
security bracket (sold separately).
y
Continue clock installation. Follow steps 1-4 for the remainder of your
clocks. You may skip step 3 and confirm clock synchronization after
some or all clocks have been hung.
n Note: Clocks will only attempt to sync to the System Controller at
approximately 2 (am & pm) and 8 (am & pm) as displayed on the clocks
and after initial power up.
Note: Do not connect power to the clocks until the System Controller is installed
and transmitting.
u
Connect clocks to AC power with cord or Molex kit and confirm green
LED is lit after power-up.
v
The LED on the back of the clock will turn red for 1 second then briefly
flash orange (1-15 flashes) indicating the receive frequency on power up.
Within 30 seconds of power up the LED will flash red or green. Red
indicates the receiver is looking for the signal and green indicates the
signal has been received. When the movement starts to correct, the LED
will turn green.
n Note: If the LED does not flash within 30 seconds, press the reset button on the
clock receiver. The LED should begin flashing within 30 seconds.
w
Within 3-5 minutes after power-up, correction should begin and the
clock hands should advance to the correct time. If clocks do not
synchronize within 20 minutes of power-up, see n Note in step 2.
x
Hang the clock using the keyhole hanger on the back of the clock or the
security bracket (sold separately).
y
Continue clock installation. Follow steps 1-4 for the remainder of your clocks.
You may skip step 3 and confirm clock synchronization after some or all clocks
have been hung.
n Note: Clocks will only attempt to sync to the System Controller at approximately
2 (am and pm) and 8 (am & pm) as displayed on the clocks and after initial
power-up or reset.
Glossary
Appendix
Tr
oubleshooting
Clock
Installation
System Contr
oller
Installation
Intr
oduction
AC
DC
To
wiring
box
AC
DC
To
wiring
box
LED
Barrel
Jack
Input
Optional
Security
Bracket
(12" shown)
Reset
Button
LED
120vac model shown
For both battery and AC clocks, we recommend first installing one clock near the
master and then one at the furthest location. Then install the remaining clocks in their
designated locations. This will simplify system troubleshooting.
Clocks should be installed within 24 hours of installing the system controller. After 24 hours, the system controller will enter Quiet Mode.
Pressing 3-5-7 on the keypad will disable Quiet Mode for 6 hours. Reference Appendix J for more details on Quiet Mode.