Verilink DIDCSU 2912 (880-502646-001) Product Manual - Manual (Page 54)

DIDCSU T1 Version
3-14 Verilink DIDCSU 2912 User Manual
Type “X” again to return to the Configuration Menu ( Figure 3-4 ).
Data Port
Configuration
Menu
To access the Data Port Configuration Menu ( Figure 3-9 ), enter “D”
from the Configuration Menu.
To change a port configuration, enter the command letter followed
by the port number. For example, to disable port 2 from service,
command In, enter “
I
2” (n is a variable that identifies the port
number).
Figure 3-9 Data Port Configuration Menu
One of the functions of the Data Port Configuration Menu is to set
the communication handshake leads between the DIDCSU data port
and your equipment (DTE).
• When the leads are set to LOW the DIDCSU always outputs a
negative voltage on the seected control lead.
• When the leads are HIGH the signal is always on, always ready.
Note that the lead options swap inputs and outputs between the
DCE or DTE data port modes.
There are three controllable diagnostic leads at the data port
(which are set up via the Data Port Diagnostics Menu):
• RLB—Remote Loopback
-- DIDCSU 2912 DATA PORT CONFIGURATION MENU -- -- DIDCSU 2912 DATA PORT CONFIGURATION MENU -- -- DIDCSU 2912 DATA PORT CONFIGURATION MENU -- -- DIDCSU 2912 DATA PORT CONFIGURATION MENU --
PORT 1 PORT 2 PORT 1 PORT 2 PORT 1 PORT 2 PORT 1 PORT 2
In) In Service YES YES In) In Service YES YES In) In Service YES YES In) In Service YES YES
Mn) Data Port Mode DCE DCE
Mn) Data Port Mode DCE DCE Mn) Data Port Mode DCE DCE Mn) Data Port Mode DCE DCE
Cn) Clock Option ST ST
Cn) Clock Option ST ST Cn) Clock Option ST ST Cn) Clock Option ST ST
On) Enable LOS detection NO NO
On) Enable LOS detection NO NO On) Enable LOS detection NO NO On) Enable LOS detection NO NO
Ln) Control Lead Mode AUTO AUTO
Ln) Control Lead Mode AUTO AUTO Ln) Control Lead Mode AUTO AUTO Ln) Control Lead Mode AUTO AUTO
SRn) Forced DTR/DSR DSR/LOW DSR/LOW
SRn) Forced DTR/DSR DSR/LOW DSR/LOW SRn) Forced DTR/DSR DSR/LOW DSR/LOW SRn) Forced DTR/DSR DSR/LOW DSR/LOW
SSn) Forced RTS/CTS CTS/LOW CTS/LOW
SSn) Forced RTS/CTS CTS/LOW CTS/LOW SSn) Forced RTS/CTS CTS/LOW CTS/LOW SSn) Forced RTS/CTS CTS/LOW CTS/LOW
SDn) Forced LLB/DCD DCD/LOW DCD/LOW
SDn) Forced LLB/DCD DCD/LOW DCD/LOW SDn) Forced LLB/DCD DCD/LOW DCD/LOW SDn) Forced LLB/DCD DCD/LOW DCD/LOW
SMn) Forced RLB/TM TM /LOW TM /LOW
SMn) Forced RLB/TM TM /LOW TM /LOW SMn) Forced RLB/TM TM /LOW TM /LOW SMn) Forced RLB/TM TM /LOW TM /LOW
DTR/LOW DTR/LOW
DTR/LOW DTR/LOW DTR/LOW DTR/LOW DTR/LOW DTR/LOW
RTS/LOW RTS/LOW
RTS/LOW RTS/LOW RTS/LOW RTS/LOW RTS/LOW RTS/LOW
LLB/LOW LLB/LOW
LLB/LOW LLB/LOW LLB/LOW LLB/LOW LLB/LOW LLB/LOW
RLB/LOW RLB/LOW
RLB/LOW RLB/LOW RLB/LOW RLB/LOW RLB/LOW RLB/LOW
Cable PRESENT PRESENT
Cable PRESENT PRESENT Cable PRESENT PRESENT Cable PRESENT PRESENT
DPL Loopback DISABLE DISABLE
DPL Loopback DISABLE DISABLE DPL Loopback DISABLE DISABLE DPL Loopback DISABLE DISABLE
Test Pattern NONE NONE
Test Pattern NONE NONE Test Pattern NONE NONE Test Pattern NONE NONE
Test Error Counter 0 0
Test Error Counter 0 0 Test Error Counter 0 0 Test Error Counter 0 0
X) exit this screen
X) exit this screen X) exit this screen X) exit this screen
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >