Pioneer DVJ-X1 - Manual (Page 47)

Advanced Operations (Operations Using Memory Cards)
43
<DRB1359> En
English
To delete information recorded on
memory cards
■ To delete individual cue/loop points
1. Press the CUE/LOOP CALL button.
¶ The preview monitor screen will display the cue point navigation
menu.
2. Use the cursor button to select the thumbnail of the cue
point you wish to erase, then press the DELETE button.
¶ The display will show the “DELETE” message, and the selected
cue point or loop point data will be erased from the memory card.
★ Data on MultiMedia cards formatted and recorded with the
CDJ-1000 or CDJ-1000MK2 cannot be deleted in this way; the
“CALL ONLY” message will appear and the delete operation
will not respond.
■ To delete all cue/loop point information for an
entire disc
1. Load the disc whose cue/loop point information you wish
to erase.
2. Hold the DELETE button depressed for 5 or more seconds.
¶ The display will scroll the “DISC DELETE? PUSH MEMORY” con-
firmation message.
3. Press the MEMORY button.
¶ All cue and loop data for the loaded disc will be deleted from the
memory card.
¶ If any button other than the MEMORY button is pressed, the de-
lete mode will be canceled.
★ Data on MultiMedia cards formatted and recorded with the
CDJ-1000 or CDJ-1000MK2 cannot be deleted in this way; the
“CALL ONLY” message will appear and the delete operation
will not respond.
■ To delete all memory card data
1. With no disc loaded, hold the DELETE button depressed
for 5 seconds or more.
¶ The display will scroll the “ALL DELETE? PUSH MEMORY” con-
firmation message.
2. Press the MEMORY button.
¶ All data will be deleted from the memory card.
¶ If any button other than the MEMORY button is pressed, the de-
lete mode will be canceled.
★ Data on MultiMedia cards formatted and recorded with the
CDJ-1000 or CDJ-1000MK2 cannot be deleted in this way; the
“CALL ONLY” message will appear and the delete operation
will not respond.
■ To copy memory card data
1. With no disc or memory card loaded:
Hold the MEMORY button pressed for 5 seconds or more.
¶ The display will scroll the “COPY MODE” “CARD A IN” mes-
sages.
2. Insert the original source memory card into the memory
card slot.
¶ The display will show the “READING” message; after several min-
utes, the “CARD B IN” message will appear.
3. Remove the source card and insert the target memory
card.
¶ Be sure to delete earlier contents of the target card to provide
sufficient recording capacity.
¶ The display will show the “WRITING” message, and after several
minutes, the “CARD A IN” message will appear.
4. Remove the target card, and once more insert the origi-
nal source card.
¶ The display will show the “READING” message; after several min-
utes, the “CARD B IN” message will appear.
5. Repeat steps 3 and 4 as required.
¶ The copying process is completed when the display shows the
“COMPLETE” message.
¶ Copying of a full 32 MB memory card will require a maximum of 3
cycles of recording steps 3-4.
¶ If the target card has insufficient memory capacity to complete
the copying process, the “Capa Err” message will appear.
¶ If you possess a computer with memory card reader, the reader can
be used to copy your memory cards (☞ P.40, precautions regarding
memory card formatting).
★ Data on MultiMedia cards formatted and recorded with the
CDJ-1000 or CDJ-1000MK2 cannot be copied to in this way;
the “CDJ CARD” message will appear and the copy opera-
tion will not respond.
ENTER
CUE/LOOP
CALL
MEMORY
DELETE