Rockwell Automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O Dual Port EtherNet/IP Adapters User Manual User Manual
Page 6
iv
Rockwell Automation Publication 1734-UM017B-EN-P - October 2013
Table of Contents
Configure the Adapter with
RSLogix5000 software
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Configuration Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Gateway Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Set the Network Address for POINT I/O Adapters . . . . . . . . . . . . . 23
Set the Network Address for ArmorPOINT I/O Adapters . . . . . . . 24
Use the Rockwell BootP/DHCP Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Configure the Adapter for Direct
Connection in RSLogix 5000
Software
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Set Up the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Create the Example Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Configure the I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Add the Local EtherNet/IP Bridge to the I/O Configuration. . . . . 33
Add the POINT I/O Adapter to the I/O Configuration. . . . . . . . . . . . . 36
Add the POINT I/O Modules to the I/O Configuration . . . . . . . . 39
Add the Digital Relay Output Module . . . . . . . . . . . . . . . . . . . . . .39
Add the Digital Sink Output Module . . . . . . . . . . . . . . . . . . . . . . .42
Edit the Controller Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Create the Ladder Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Download the Program to the Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Verify the Module Chassis Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Configure the Adapter with Fixed IP Address. . . . . . . . . . . . . . . . . . . . . . . 50
Recover From an Overloaded Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Chapter Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Configure the Adapter for Direct
Connection and Rack
Optimization in RSLogix 5000
Software
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Set Up the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Set Up the POINT I/O Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Create the Example Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Configure the I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Add the Local EtherNet/IP Bridge to the I/O Configuration. . . . . 56
Add the POINT I/O Adapter to the I/O Configuration. . . . . . . . . . . . . 60