Configuring pe 2, Spanning tree configuration example, Network requirements – H3C Technologies H3C S12500-X Series Switches User Manual
Page 147
136
3.
Configure Ten-GigabitEthernet 1/0/3 (a customer-side port):
# Configure Ten-GigabitEthernet 1/0/3 as a trunk port, and assign it to VLAN 200 and VLANs 30
through 90.
[PE1] interface ten-gigabitethernet 1/0/3
[PE1-Ten-GigabitEthernet1/0/3] port link-type trunk
[PE1-Ten-GigabitEthernet1/0/3] port trunk permit vlan 200 30 to 90
# Set the PVID to 200 on the port.
[PE1-Ten-GigabitEthernet1/0/3] port trunk pvid vlan 200
# Enable QinQ on the port.
[PE1-Ten-GigabitEthernet1/0/3] qinq enable
[PE1-Ten-GigabitEthernet1/0/3] quit
Configuring PE 2
1.
Configure Ten-GigabitEthernet 1/0/1 (a customer-side port):
# Configure Ten-GigabitEthernet 1/0/1 as a trunk port, and assign it to VLAN 200 and VLAN 30
through VLAN 90.
<PE2> system-view
[PE2] interface ten-gigabitethernet 1/0/1
[PE2-Ten-GigabitEthernet1/0/1] port link-type trunk
[PE2-Ten-GigabitEthernet1/0/1] port trunk permit vlan 200 30 to 90
# Set the PVID to 200 on the port.
[PE2-Ten-GigabitEthernet1/0/1] port trunk pvid vlan 200
# Enable QinQ on the port.
[PE2-Ten-GigabitEthernet1/0/1] qinq enable
[PE2-Ten-GigabitEthernet1/0/1] quit
2.
Configure Ten-GigabitEthernet 1/0/2 (the service provider-side port):
# Configure Ten-GigabitEthernet 1/0/2 as a trunk port, and assign it to VLAN 100 and VLAN
200.
[PE2] interface ten-gigabitethernet 1/0/2
[PE2-Ten-GigabitEthernet1/0/2] port link-type trunk
[PE2-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 200
# Set the SVLAN TPID to 0x8200 on the port.
[PE2-Ten-GigabitEthernet1/0/2] qinq ethernet-type service-tag 8200
[PE2-Ten-GigabitEthernet1/0/2] quit
3.
Configure Ten-GigabitEthernet 1/0/3 (a customer-side port):
# Configure Ten-GigabitEthernet 1/0/3 as a trunk port, and assign it to VLAN 100 and VLAN 10
through VLAN 70.
[PE2] interface ten-gigabitethernet 1/0/3
[PE2-Ten-GigabitEthernet1/0/3] port link-type trunk
[PE2-Ten-GigabitEthernet1/0/3] port trunk permit vlan 100 10 to 70
#Set the PVID to 100 on the port.
[PE2-Ten-GigabitEthernet1/0/3] port trunk pvid vlan 100
# Enable QinQ on the port.
[PE2-Ten-GigabitEthernet1/0/3] qinq enable
[PE2-Ten-GigabitEthernet1/0/3] quit