Icom IC-7000 - Manual (Page 11)

✔ What is the PBT control?
PBT electronically narrows the IF passband width to reject
interference. This transceiver uses DSP to implement PBT.
➥While M-ch/RIT is selected:
● ● Rotate the inner control to select a memory
channel number (p. 102).
● ● Push inner control for 1 sec. to turn the
RIT/
∂TX mode ON (pgs. 75, 88).
• Push [ Z(
MENU
/
GRP
)] to exit the RIT/ ∂TX mode.
● ● While the RIT/∂TX mode is OFF:
Rotates outer control to select a memory bank
(p. 106).
● ● While the RIT/∂TX is ON:
Rotate outer control to shift the receive or
transmit frequency (pgs. 75, 88).
• “ ” or “ ” indicators appear when the RIT or
∂TX function is activate, respectively.
• The shift frequency range is ± 9.999 kHz in 1 Hz
steps (or ±9.99 kHz in 10 Hz steps).
• When the RIT or ∂TX function is ON, push and
hold [F-1 RIT] or [F-2 ∂TX] for 1 sec. to add or
subtract the frequency shift to the display fre-
quency.
✔ What is the RIT function?
RIT (Receiver Incremental Tuning) shifts the receive fre-
quency without shifting the transmit frequency.
This is useful for fine tuning for stations calling you off fre-
quency or when you prefer to listen to slightly different-
sounding voice characteristics, etc.
✔ What is the ∂TX function?
The ∂TX shifts the transmit frequency without shifting the re-
ceive frequency. This is useful for simple split frequency op-
eration in CW, etc.
yTWIN PBT (M-ch/RIT) INDICATOR
(pgs. 75, 79, 88, 102)
➥Indicates the status of [PBT/M-ch/RIT] (t) acti-
vates as the Twin PBT function or memory chan-
nel/RIT control.
• Indicator is green when the Twin PBT is selected.
• Indicator is off when the M-ch/RIT is selected.
• Indicator is orange when the RIT or
∂TX function is
activate.
uMENU/GROUP KEYS [MENU/GRP] (p. 153)
➥Push either key one or more times to select
menus within a menu group (M, S or G (Graphic)).
➥Push and hold for 1 sec. to select one of the three
menu groups: M-1 to M-3, S-1 to S-3 and G-1
(Scope) to G-3 (SWR meter).
iTUNER/CALL KEY [TUNER/CALL]
➥During HF/50 MHz operation (p. 116):
● ● Push momentarily to toggle the automatic an-
tenna tuner function ON and OFF.
• An optional antenna tuner must be connected.
• “
” indicator appears when the tuner is ON.
● ● Push and hold for 2 sec. to manually tune the
antenna.
• An optional antenna tuner must be connected.
• “
” indicator appears when the tuner is ON.
➥During 144/430 MHz operation (p. 102):
Push momentarily to select the call channel (or
return to the previous channel/frequency when
the call channel is already selected).
• “C1” is the 144 MHz call channel and “C2” is the 430
MHz call channel.
oMULTI-FUNCTION KEYS [F-1]/[F-2]/[F-3]/[F-4]
➥Push to select the function indicated in the LCD
display above these keys. (pgs. 5–8, 153)
• Functions vary depending on the active menu.
Functions appear
M-ch
RIT
M-ch RIT
Frequency
decreases Frequency
increases Channel
decreases Channel
increases
2
1
PANEL DESCRIPTION
1
See the illustration of the Front panel on page i-2.