Toshiba STRATA CIX - Manual (Page 98)

Telephone Button Programming
800 Series Programs
1-94
Strata CIX/CTX Telephone Button Programming 11/04
800 Series Programs
Table 1-39 Programs 801~803
Button Sequence Value(s) Summary
801 Network Jack LAN
Device Assignments
801 , Hold
This screen assigns the LAN parameters for the PC applications
connected to the BECU Network Jack through a LAN or Hub.
801-00 LAN Port Number
n, Hold
n = 1~12 (default = no value) Enter the port number of the LAN device to be assigned. Refer to
Program 803 SMDR SMDI CTI Port Assignments.
Notes
• Program the local port number for LCD Control of Voice Mail
• Use the same Device Port No. (11) for Network BLF.
• Use 10 for Network CTX Proprietary Integration
• Use 12 for Network DSS
Network BLF and DSS are available only with CTX Release 1.3 or
higher software and with CTX WinAdmin Release 1.3 or higher
software.
801-01 Protocol
FB01 , n, Hold
n = 1. TCP (default)
2. UDP
Select communication Protocol.
Note Select UDP for Network DSS.
801-02 PC Operation Type
FB02 , n, Hold
n = 1. Server (default)
2. Client
Enter the application PC type: Server or Client.
801-03 Data Flow
FB03 , n, Hold
n = 1. Synchronization
2. Asynchronization
(default)
Enter the data flow protocol that should take place between the CTX
and PC. If the PC is a CTX, CTI application assign ìAsynchronizationî
to data flow.
801-04 Server Port Number
FB04 , n, Hold
n = 0~65535 (default = 0) Enter the Server Port Number and proceed to 07 Read Retry
Number . This field is required if Server was selected in 02 PC
Operation Type above. If not, leave this field blank and proceed to 05
Client IP Address .
Note Use 6000 for Network BLF, 3000 for Network DSS, and 5000
for Network CTX Proprietary Integration.
801-05 Client IP Address
FB05, FB06, FB07,
or FB08
, n, Hold
n = 0~255 (default = 0) Enter the Client LAN IP Address. This field is required if Client was
selected in
02 PC Operation Type above.
0~255 for each octet (default = 0)
Enter IP address of Stratagy iES32 or SES.
801-06
801-07
801-08
801-09 Write Retry Number
FB09 , n, Hold
n = 0~65535 (default = 0) Enter the Client Port number. This field is required if Client was
selected in
02 PC Operation Type above.
801-10 Write Retry Number
FB10 , n, Hold
n = 0~10 (default = 1) Set the Read Retry counter to (1~10).
801-11 Write Retry Number
FB11 , n, Hold , Hold
n = 0~10 (default = 1) Set the Write Retry counter to (1~10).
803 IO Logical Device
Assignment
803 , Hold
This screen is used to assign:
1. SMDR and SMDI to logical device and BSIS, RS-232 port
numbers.
2. CTX WinAdmin, ACD sever, and Attendant Console to BECU,
Network Jack logical device and LAN port numbers.
803-00 Logical Device
Number
n, Hold
n = 100 = SMDR
300 or 301 = SMDI
200~208 = CTI LAN
Devices of PCs (default =
no value)
400 = BLF
500 = DSS Enter the 3-digit logical device number for SMDR, SMDI, and LAN
device or PC application. See
ìDevice Tableî on page 1-95
SMDR: 100
SMDI: 300 or 301
CTI LAN devices or PCs can be assigned to any of the 9 LAN devices
numbers available: 200~208.