Zoom MRS-1044 - Manual (Page 100)

ZOOM MRS-1044
100
Appendices
Effect type/parameter list
TYPE = PDL-WAH : 1 – 50
TYPE = EXCITER : 1 – 5
1 – 8
OFF / On
bPF / LPF
1 – 10
-10 – 10
-12.0 – 24.0
0 – 10
0 – 30
0 – 10
1 – 10
TYPE = WIDE : 1 – 64
TYPE = DELAY : 1 – 50
0 – 30
0 – 30
Specifies the center frequency of the wah.
Specifies the frequency.
Sets the output level of the module.
Specifies whether the expression pedal will be used as a wah pedal.
Specifies the type of filter.
Adds character to the sound.
Adjusts the sensitivity with which the effect is applied.
Sets the amount of shift produced by the pitch shifter.
Adjust the tone.
Adjusts the balance between the direct sound and effect sound.
Emphasizes the low-frequency range.
Specifies the spatial width.
Sets the delay time.
Adjusts the mix amount of the effect sound.
Adjusts the mix amount of the direct sound.
FREQ
LEVEL
RTM
FLT TYPE
RESO
SENS
SHIFT
TONE
BALANCE
LowBoost
SIZE
TIME
WET LVL
DRY LVL
0 – 15
0 – 15
0 – 15
0 – 15
1 – 8
Adjusts the input sensitivity of compression.
Adjusts the speed at which compression is applied.
Adjusts the sensitivity at which the limiter begins to apply.
Specifies the length from when the input signal level falls below the threshold until
compression ends.
Specifies the output level of the module.
Range Explanation of parameter Parameter name
SENS
SENS 1
SENS 2
ATTACK
ATTACK_1
ATTACK_2
THRSHLD
THRSH_1
THRES_2
RELEASE
RELEASE1
RELEASE2
LEVEL
LEVEL_1
LEVEL_2
SINGLE
DUAL ( Lch )
DUAL ( Rch )
SINGLE
DUAL ( Lch )
DUAL ( Rch )
SINGLE
DUAL ( Lch )
DUAL ( Rch )
SINGLE
DUAL ( Lch )
DUAL ( Rch )
SINGLE
DUAL ( Lch )
DUAL ( Rch )
Explanation of COMP/LIM MODULE parameters
■ MIC ALGORITHM
A mono input/output compressor.
A mono input/output limiter.
A two-channel input/output compressor. Parameters for left and right can be set independently.
A two-channel input/output limiter. Parameters for left and right can be set independently.
PARAMETER 1 PARAMETER 2 PARAMETER 3 PARAMETER 4 PARAMETER 5 PARAMETER 6 TYPE
SINGLE
COMP x1
SINGLE
LIMIITx1
DUAL
COMP x2
DUAL
LIMIITx2
ATTACK
RELEASE
ATTACK_1
RELEASE1
SENS
THRSHOLD
SENS_1
THRSH_1
LEVEL
LEVEL
LEVEL_1
LEVEL_1
--
--
SENS_2
THRES_2
--
--
ATTACK_2
RELEASE2
--
--
LEVEL_2
LEVEL_2
COMP/LIM MODULE
*1: When a SINGLE type effect is selected for the COMP/LIM module
*2: When a DUAL type effect is selected for the COMP/LIM module
A pre-amp for use with an external mic.
A pre-amp for use with an external mic.
PARAMETER 1 PARAMETER 2 PARAMETER 3 PARAMETER 4 PARAMETER 5 PARAMETER 6 TYPE
MIC PRE (*1)
MIC PRE (*2)
TONE
TONE 1
COLOR
COLOR 1
LEVEL
LEVEL 1
DE-ESSER
COLOR 2
--
TONE 2
--
LEVEL 2
MIC PRE MODULE
0 – 10
1 – 30
0 – 30
TYPE = FLANGER : -10 – 10
TYPE = DELAY : 0 – 10
AF / bF
1 – 4
0 – 10
Adjusts the depth of the effect.
Adjusts the speed of the effect.
Adjusts the mix amount of the effect.
Adjusts the amount of feedback.
Exchanges the effect locations of the DRIVE module and MOD module.
Changes the type of the phase tone.
Emphasizes the effect.
Range Explanation of parameter Parameter name
DEPTH
RATE
MIX
FB
POSITION
COLOR
CLIP
Explanation of MODULATION/DELAY MODULE parameters