Yokogawa RotaMASS 3-Series - Manual (Page 177)

APPENdIX 8. dEVICEVIEWEr WINdOW EXECUTEd FrOM FIELdMATE ANd PrM
a-77
IM 01R04B05-00E-E 3rd edition July 30, 2010 -00 all Rights Reserved. Copyright © 2005, Rota Yokogawa
Figure A8.3 Configuration (Mandatory)
Table A8.3 Configuration (Mandatory)
RB in o/S Mode(a-21) alarm Resource Block is in o/S mode. (a-21)
[Remedy]: Change the RB Block Mode.target(RB.MoDE_BLK.target) to auto mode.
tB in o/S Mode(a-22 alarm transducer Block is in o/S mode. (a-22)
[Remedy]: Change the tB Block Mode.target(tB.MoDE_BLK.target) to auto mode.
aI1 in o/S Mode(a-23) alarm aI1 Block is in o/S mode. (a-23)
[Remedy]: Change the aI1 Block Mode.target(aI1.MoDE_BLK.target) to auto or other mode.
In addition, check that RB Block Mode.actual(RB.MoDE_BLK.actual) is set to auto mode.
If it is an unused function, set aLaRM_PERFoRM bit0 to 0.
aI2 in o/S Mode(a-24) alarm aI2 Block is in o/S mode. (a-24)
[Remedy]: Change the aI2 Block Mode.target(aI2.MoDE_BLK.target) to auto or other mode.
In addition, check that RB Block Mode.actual(RB.MoDE_BLK.actual) is set to auto mode.
If it is an unused function, set aLaRM_PERFoRM bit1 to 0.
aI3 in o/S Mode(a-25) alarm aI3 Block is in o/S mode. (a-25)
[Remedy]: Change the aI3 Block Mode.target(aI3.MoDE_BLK.target) to auto or other mode.
In addition, check that RB Block Mode.actual(RB.MoDE_BLK.actual) is set to auto mode.
If it is an unused function, set aLaRM_PERFoRM bit2 to 0.
aI4 in o/S Mode(a-26) alarm aI4 Block is in o/S mode. (a-26)
[Remedy]: Change the aI4 Block Mode.target(aI4.MoDE_BLK.target) to auto or other mode.
In addition, check that RB Block Mode.actual(RB.MoDE_BLK.actual) is set to auto mode.
If it is an unused function, set aLaRM_PERFoRM bit3 to 0.
Display out of Range(a-41) alarm Display value is out of range. (a-41)
[Remedy]: Change decimal point.
aI1 in Man Mode(W-21) Warning aI1 Block is in Man mode. (W-21)
[Remedy]: Change the aI1 Block Mode.target(aI1.MoDE_BLK.target) to auto or other mode.
aI2 in Man Mode(W-22) Warning aI2 Block is in Man mode. (W-22)
[Remedy]: Change the aI2 Block Mode.target(aI2.MoDE_BLK.target) to auto or other mode.
aI3 in Man Mode(W-23) Warning aI3 Block is in Man mode. (W-23)
[Remedy]: Change the aI3 Block Mode.target(aI3.MoDE_BLK.target) to auto or other mode.
aI4 in Man Mode(W-24) Warning aI4 Block is in Man mode. (W-24)
[Remedy]: Change the aI4 Block Mode.target(aI4.MoDE_BLK.target) to auto or other mode.
aI1 Simulation active(W-41) Warning aI1 Block is simulation mode. (W-41)
[Remedy]: Change the aI1 Simulation En/Disable(aI1.SIMuLatE.SIMuLatE_EnaBLE) to Disabled.
aI2 Simulation active(W-42) Warning aI2 Block is simulation mode. (W-42)
[Remedy]: Change the aI2 Simulation En/Disable(aI2.SIMuLatE.SIMuLatE_EnaBLE) to Disabled.
aI3 Simulation active(W-43) Warning aI3 Block is simulation mode. (W-43)
[Remedy]: Change the aI3 Simulation En/Disable(aI3.SIMuLatE.SIMuLatE_EnaBLE) to Disabled.
aI4 Simulation active(W-44) Warning aI4 Block is simulation mode. (W-44)
[Remedy]: Change the aI4 Simulation En/Disable(aI4.SIMuLatE.SIMuLatE_EnaBLE) to Disabled.