Rockwell Automation GV3000/SE AC Bookshelf Drive Hardware Ref, Installation, and Troubleshooting - Manual (Page 93)

Index Index-3
N
Network
AutoMax Network Option board, 2-11, 2-12
communication, 2-11
ControlNet Network Option board, 2-12
DeviceNet Network Option board, 2-11, 2-13
Profibus Network Option board, 2-13
O
Open loop control, see Volts/Hertz Regulation
Operator Interface Module, 2-13
Operator Interface Module connector, 2-11
Option kits,
see Kits
Option board connector, 2-6, 2-11
Output
analog, see analog Output
contactors, 6-1
digital,
see Status Relays
specifications, terminal strip, A-2
Output relay terminal strip, 2-3, 2-4, 2-5, 2-12, 3-6,
7-2, 7-14
Overload, motor, 6-1
P
Parts
location, see Component Locations
replacement, 10-7
PC control, see Control Source
Power board, 2-3, 2-4, 2-5, 2-6
Power ratings, 2-2
Power terminals
torque specifications, 5-2
wiring, 3-5 to 3-6, 4-2 to 4-5, 5-1 to 5-3, 6-1 to
6-2
Profibus Network Option board, 2-13
Protection, mechanical motor overload, 6-1
Publications, related, 1-1
R
Ramp 1/Ramp 2 (digital input 7), 2-10, 7-2, 7-10
Rating
AC input, 2-2
enclosure, 2-2
fuse, 3-8 to 3-9
output, 2-2
power loss, 2-2
Regulator board, 2-3, 2-4, 2-5, 2-6 to 2-11, 7-1 to
7-3, 7-7 to 7-13, 10-7
Relays, output status, see Status Relays
Reliance, getting assistance from, 1-1
Remote (digital input 8), 2-10, 7-2, 7-9
Remote Meter Interface board, 2-13
Removing cover, 10-1 to 10-2
Replacement parts, 10-5
Reset (digital input 3), 2-10, 7-2, 7-13
Reverse (digital input 6), 2-10, 7-2, 7-11
RS-232
cable length, 3-8
communication port (X8), 2-6, 2-10, 3-8
Run (digital input 4), 2-10, 7-2, 7-12
S
Selecting operation, see Control Source
Sensorless vector control, 2-1
Serial communication,
see RS-232
Site requirements, 3-1 to 3-2
Software, drive, 1-1
Space requirements,
2 to 30 amp drives, 3-3
43 amp drives, 3-4
Specifications, technical, A-1 to A-3
Speed, maximum setting, 7-5
Start (digital input 1), 2-10, 7-2, 7-13
Status relays, Form A/B, 2-12, 7-2, 7-14
Stop (digital input 2), 2-10, 7-2, 7-13
Stopping the drive, 7-4 to 7-5
Super Remote Meter Interface board, 2-13
SVC, see Sensorless Vector Control
Switch, membrane,
see Keypad/Display
T
Tachometer, pulse, see Encoder
Terminal strip,
input specifications, A-2
output specifications, A-2
output relay, 2-3, 2-4, 2-5, 2-12, 7-2, 7-14
Regulator board, 2-6, 2-10, 7-1 to 7-13
torque specifications, 3-6
wiring, 2-10, 3-6, 7-1 to 7-14
Testing, IGBT, 10-4 to 10-6
Transformer, installing isolation input, 5-1
Transients, AC line voltage, 5-1
V
Vector regulation, 2-1
Ventilation,
see Air Flow
Volts/hertz regulation, 2-1