Quintum Technologies Tenor Call Relay SP - Manual (Page 76)

P/N 480-0048-00-10 7-10
Chapter 7: Call Detail Recording
Sample Record for Extended Call Relay SP CDR Format 3, 4, 103, 104:
Record 1 Sample: (includes fields for formats 3 and 103)
1,17325551212,15,20000207062812,21060207062815,2000020706283030,Blank,208.226.140.57,192.16
8.10.64,Blank,1,1,Blank, Blank, Blank,Blank, Blank, Blank, Blank, Blank,Blank,0,0,1415551000,Blank,
0123456789,9876543210,12138765432
Record 1 Field Definitions - Call Relay SP Extended Formats (3 and 103)
1 (Call ID), 17325551212 (Called Number), 15 (Duration), 20000207062812 (Call Initiation Time),
20000207062815 (Call Connected Time), 2000020706283030 (Call Disconnected Time), Blank (Cause
Code), 208.226.140.57 (Incoming LEG IP Address), 192.168.10.64 (Outgoing LEG IP Address),
Blank (Origination Trunk ID), 1 (Call Type), 1 (Call Number Type), Blank (Incoming Slot), Blank
(Incoming Device), Blank (Incoming Digital Interface), Blank (Incoming Channel), Blank (Outgoing
Slot), Blank (Outgoing Device), Blank (Outgoing Digital Interface), Blank (Outgoing Channel), Blank
(AutoSwitch Time), 0 (AutoSwitch Duration), 0 (Bad IP Quality Events), 0 (AutoSwitch Flag),
1415551000 (Calling Party Number), Blank (PIN Code), 0123456789 (Local Call ID #), 9876543210
(Remote Call ID #)
The 4 and 104 extended format includes all fields used in the 3 and 103 extended format plus the following
field:
12138765432 (Incoming/Outgoing IP DN).
Definitions for each field appears below.
Call ID: Sequence number. This is a unique number assigned to identify an individual call (i.e, 1, 2, 3,…).
The sequence number starts from 1 and wraps around at 4,294,967,295. When a Tenor unit resets, the
sequence number starts from 1 again. If the system has a problem and loses connectivity, the CDR server can
send the Call Relay SP unit the last Call ID that it received. The Call Relay SP unit will reply with all records
that contain a Call ID which is greater than the one last received.
Called #: The number called. This will be in international format except for a pass-through call going from
PBX to PSTN or call going from PSTN to PBX.
Duration: Call duration. This value is in seconds, the value will be 0 if never connected.
Call Initiation Time: The date and time the call initiated. The time will be the local time configured on the
Call Relay SP unit. The entry will be in the following format: yyyymmddhhmmss where yyyy (4 digits for
year), mm (2 digits for month), dd (2 digits for day), hh (2 digits for hour), mm (2 digits for minutes), ss (2
digits for seconds).
Call Connected Time: The date and time the call was actually connected. The time will be the local time con-
figured on the Call Relay SP unit. The entry will be in the following format: yyyymmddhhmmss where yyyy
(4 digits for year), mm (2 digits for month), dd (2 digits for day), hh (2 digits for hour), mm (2 digits for min-
utes), ss (2 digits for seconds). This field will be blank if the call never connected.
Call Disconnected Time: The date and time the call disconnected. The time will be the local time configured
on the Call Relay SP unit. The entry will be in the following format: yyyymmddhhmmss where yyyy (4 digits
for year), mm (2 digits for month), dd (2 digits for day), hh (2 digits for hour), mm (2 digits for minutes), ss (2
digits for seconds).