Rice Lake MSI-9850 CellScale RF Digital Indicator - Operator Manual - Manual (Page 32)

Page 32 MSI-9850 RF Remote Indicator • User Guide
MSI-9850
HANDHELD RF REMOTE INDICATOR for
C
ELL
S
CALE
®
the scale will zero.
3) The scale will accept a zero setting over the full Range of the scale (NTEP and other Legal-for-trade models may
have a limited zero range). Zero settings above 4% of full scale will subtract from the overall capacity of the scale.
For example if you zero out 100 lb. on a 1000 lb. scale the overall capacity of the scale will reduce to 900 lb. plus
the allowed over-range amount.
TARE
Tare is typically used to zero out a known weight such as a packing container or pallet and display the load in
NET weight. A Tare value is entered in either of two ways:
1) PUSH BUTTON TARE – When the TARE key is pressed, the current weight is zeroed and Net Weight is
displayed.
2) KEYBOARD TARE – Using the numeric keys, the operator keys in the desired Tare Weight then presses the
TARE Key.
For Pushbutton Tare
To Clear Tare and Revert to Gross Mode
If the goal is to see the Gross Weight, use the Net/Gross key instead.
TARE
T
TARING
1) In single channel mode, go to step 2. In multi-channel mode, highlight a channel
with the up ( ^ ) or down ( v ) cursor keys to make it active.
2) Press TARE . The current Gross Weight will be stored in the Tare register and
the weight mode will change to NET (single display modes).
0
SPACE
TARE
T
1) In single channel mode, go to step 2. In multi-channel mode, highlight a channel with the
up ( ^ ) or down ( v ) cursor keys to make it active.
2) Press [0] followed by TARE . The Tare value will clear and the scale returns to the GROSS
mode.
Alternate method: Remove all weight from the scale (Gross Zero) and press TARE. The message display temporarily reads “TARING”.
Then the scale returns to the GROSS mode.
To Keyboard Tare
To View the Tare Value on the LED Display
The default function for ENTER-NET/GROSS is “View Tare”. This function can also be assigned to any F-Key.
2
0
SPACE EXIT
5
MNO
3
TARE
T
1) In single channel mode, go to step 2. In multi-channel mode, highlight a channel with
the up ( ^ ) or down ( v ) cursor keys to make it active.
2) Using the numeric keys input the value desired. In this example we’ll use 0.5 lb. as
a Tare Value. Press [0] [.] [5] . The Enter Line displays “0.5”.
You must place a leading zero if the Tare value is less than 1.
3) Press TARE to place the value in the Tare Register (Current Channel, current ID).
The display reads “TARE SET” when the CellScale responds. All subsequent read-
ings have the Tare value subtracted and are displayed in “NET” weight.
To View and/or Change the Tare Value
2
ENTER TARE
T
1) In single channel mode, go to step 2. In multi-channel mode, highlight a channel with
the up ( ^ ) or down ( v ) cursor keys to make it active.
2) Press ENTER followed by TARE .
3) The display shows the current Tare value for 5 seconds
You can edit the Tare value from this screen by pressing number keys.
2
ENTER TARE
T
1) In single channel mode, go to step 2. In multi-channel mode, highlight a channel with
the up ( ^ ) or down ( v ) cursor keys to make it active and place it on the LED.
2) Press ENTER followed by DISPLAY .
3) The LED display shows the current Tare value for 5 seconds
Go to Index