Rice Lake MSI-9850 CellScale RF Digital Indicator - Operator Manual - Manual (Page 45)

MSI CellScale ® System • 9850 User Guide Page 45
MEASUREMENT SYSTEMS INTERNATIONAL
Firmware Version 5-XX for 2450 Modems
SETUP ID CODES MENU
Allows setup of ID Codes. A new ID can be created, the 8 character ID Name can be edited, two 20 character
print strings can be assigned to each ID Code. Also any or all IDs can be deleted from this menu.
In the Product ID menus the
ID , CHANNEL , and ADDRESS keys are active. This allows you to setup IDs for
all channels on any programmed network without leaving the menu.
SETUP SELECT MENU
1 Function Keys
2 Set Points
3 System
4 Password Locks
5 BarCode
6 Total
7 MORE 1/2
PRODUCT ID Chan X-X
Net XX ID IDName--
1 New Product ID
2 ID Units kg
3 Edit ID Strings
4 Edit ID Name
5 Display Mode NORM
CLR Delete ID(s)
SETUP SELECT MENU
1 Channel & Calibrate
2 Scale Display Line
3 RF Modem
4 Comm 2 & Strings
5 Product ID Codes
6 Tare
7 MORE 2/2
Shortcut
Len 0 F4 Menu
Max 8 ENT Save
Pos 1
Prod ID Name
PRODUCT ID Chan X-X
Net XX ID IDName--
1 Edit ID String 1
-ID String 1-
2 Copy prev String 1
3 Edit ID String 2
-ID String 2-
4 Copy prev String 2
2 ID Units kg
Len 0 F4 Menu
Max 20 ENT Save
Pos 1
ID String 1
2 ID Units lb
Steps through available units
(defined at CellScale)
1
1
Delete This ID
Are You Sure?
ENTER = Yes, Delete
ESC = No, Cancel
CLR = Delete All IDs
Delete All IDs
Are You Sure?
Deletes all Totals,
Stats,Names,Strings
ENTER = Delete All
ESC = No, Cancel
5 Display Mode NORM
5 Display Mode %
5 Display Mode OFF
SETUP SELECT MENU SETUP SELECT MENU PRODUCT ID Chan X-X
ZERO
CLR
0
ZERO
CLR
0
ESC
!
SETUP
ESC
!
SETUP
ID
F6
PRODUCT ID MENU
1) New Product ID – Calls a text enter screen for creating a new
ID. Use the alphanumeric keypad to enter any name up to 8
characters.
See “General Text Entry” for further information for text entry.
2) ID Units – Pressing [2] steps through the available units for
this channel and selects the units used for this ID
3) Edit ID Strings – Brings up a submenu for selection of ID
String 1 or 2.
4) Edit ID Name – Allows editing the 8 character ID name without
creating a new ID.
5) Display Mode – Should usually be left in the default condition
of “NORM”. Pressing [5] selects a per cent display mode (1%
resolution), or display ID disabled mode (OFF).
CLR
Delete ID(s) – Deletes current displayed ID (won’t delete ID1,
the default ID). Returns to channel default ID1 when finished.
Press ENTER on the “Are You Sure?” screen to complete the
deletion. Any other key (except CLR ) cancels the deletion.
From the “Are You Sure” screen, pressing CLR again will
allow you to “Delete All IDs” – Deletes every ID on the active
channel. Press ENTER on the “Are You Sure?” screen to
complete the deletion. Any other key cancels the deletions.
EDIT ID STRINGS SUBMENU
1) Edit ID String 1 – Brings up a text entry screen. Enter or edit
up to 20 characters. The current ID string is shown below
selection 1.
2) Copy previous String 1 – Pressing 2 causes the last pro-
grammed String 1 to be copied into this IDs string 1. Use the
ID key or Channel key from this menu to activate other IDs
for the copy operation.
3) Edit ID String 2 – Brings up a text entry screen. Enter or edit
up to 20 characters. The current ID string is shown below
selection 3.
4) Copy previous String 2 – Pressing 2 causes the last pro-
grammed String 2 to be copied into this IDs string 2. Use the
ID key or Channel key from this menu to activate other IDs
for the copy operation.
Go to Index