Rice Lake MSI-9850 CellScale RF Digital Indicator - Operator Manual - Manual (Page 74)

Page 74 MSI-9850 RF Remote Indicator • User Guide
MSI-9850
HANDHELD RF REMOTE INDICATOR for
C
ELL
S
CALE
®
SETUP SELECT MENU
1 Function Keys
2 Set Points
3 System
4 Password Locks
5 Display Preview
6 Total
7 MORE 1/2
COMM PORT 2
1 Enter/Edit Strings
2 Output Interval
3 Control Settings
4 Serial Settings
5 Motion Check ON
6 Data Logging
SETUP SELECT MENU
1 Channel & Calibrate
2 Display
3 RF Modem
4 Comm 2 & Strings
5 Product ID Codes
6 Tare
7 MORE 2/2
BAUD RATE
1 3ØØ 8 19.2k
2 6ØØ 9 28.8k
3 12ШШ Ш 38.4k
4 24ØØ F1 57.6k
5 48ØØ F2 76.8k
6 96ØØ F3 115.2k
7 14.4k F4 23Ø.4k
2 Data Bits 7
2 Data Bits 8
HANDSHAKING
1 Hardware DCE
2 Hardware DTE
3 Hardware RTR/CTS
4 None
5 Software XON/XOFF
MODE
1 Duplex
2 Listen
3 Off
4 Talk
Text Editing
Screen. See
general text
editing
section.
INTERVAL MILLISECOND
ESC exits no change
ENTER saves value
Ø-9 replaces value
5Ø
min = Ø, max = 95Ø
^ incs, v decs digit
Shortcut
6
TRIGGER PRINT ON
-Current Mode-
1 Total
2 Set Point 1 (SP1)
3 Set Point 2 (SP2)
4 SP1 And SP2
5 SP1 Or SP2
6 MORE 2/2
TRIGGER PRINT ON
-Current Mode-
1 Continuously
2 Send/Print Key
3 Comm 2 CTS
4 Weight Change
5 Stable Load
6 MORE 1/2
COMM 1 STRINGS
1 Data Out String
2 End of Line
3 Start of Line
4 Wait Character
5 Aux String
6 Ack String
7 Overload String
OUTPUT INTERVAL
Print Once on Trig
1 Milliseconds
2 Seconds
3 Minutes
4 Hours
5 Days
CLR = Print Once
SERIAL SETTINGS
1 Baud Rate 96ØØ
2 Data Bits 8
3 Parity NONE
4 Handshake NONE
5 Mode DUPLEX
6 Setup Settings Dump
5 Motion Check OFF
5 Motion Check ON
DATA LOGGING
1 Output Memory 1
2 Output Memory 2
3 Abort Output
4 Erase Memory 1 XX%
5 Erase Memory 2 XX%
6 FKey to Memory 1
7 AutoPrint to Mem 1
AUTO PRINT TO MEMORY
1 Print to Memory 1
2 Print to Memory 2
3 Auto Log Msg OFF
4 Auto Clr IDStr1 OFF
5 Auto Clr IDStr2 OFF
6 Bar1 OFF 8 Bar3 OFF
7 Bar2 OFF 9 Bar4 OFF
3 Parity EVEN
3 Parity NONE
3 Parity ODD
1-5 Key
1 Key shown
for example
NET/GROSS
B/G
COMM 1 STRINGS
OUTPUT INTERVAL
TRIGGER PRINT ON
TRIGGER PRINT ON
SERIAL SETTINGS
DATA LOGGING
COMM PORT 2
SETUP SELECT MENU
INTERVAL MILLISECONDS
BAUD RATE
HANDSHAKING
MODE
AUTO PRINT TO MEMORY
SETUP SELECT MENU
ESC
!
SETUP
IN
F3
SEND/PRINT
will output data at the highest rate possible (also limited by the transmission rate from the CellScale). Interval
used with other control modes can be useful for control and monitoring purposes.
[3] TRIGGER PRINT ON: The “Trigger Print On’ menu designates the condition that causes the 9850 to output data. The
Send / Print key will always work unless specifically locked out or the function key is reassigned. When the designated trigger
“Text Messag-
ing” for more
detail. This
string defaults
to the ASCII
A C K c o m -
mand but any
message up to
32 bytes can be
entered.
7) O v e r l o a d
String: Eight
characters long
is sent instead
o f w e i g h t
w h e n t h e
scale is over-
loaded. Used
when a score-
board cannot
display the
alphanumeric
string “OVER-
LOAD”.
[ 2 ] OUTPUT
I N T E R V A L :
Selecting “Print
Once” CLR means
that after the trigger
condition, a single
transmission of data
will occur. For con-
tinuous output, a
print interval can
be entered from
50ms to 50 days in
50ms increments.
Used in conjunction
with the Continuous
Trigger mode, this
can generate a time
based data-logging
system. An interval
of 50 milliseconds
means that the scale
Go to Index