Rice Lake MSI-9850 CellScale RF Digital Indicator - Operator Manual - Manual (Page 48)

Page 48 MSI-9850 RF Remote Indicator • User Guide
MSI-9850
HANDHELD RF REMOTE INDICATOR for
C
ELL
S
CALE
®
SECTION 7 – TOTAL / STATISTICS
TOTAL
• The 9850 can add independent weighments together and keep a counter of how many weighments were added
(Totaled). The Weighments counter can be thought of as a box or palette counter.
• “TOTAL” always uses the displayed weight, so gross and net readings can be added into the same total.
• There are two modes of Totaling which are set in the SETUP TOTAL section. The Manual mode uses the
TOTAL key to add the current weight to the previously totaled value. The Auto mode will automatically add
the last, settled value to the total (or optionally the highest value). See “SETUP TOTAL” for instructions to
enable the AUTO TOTAL modes.
• Both modes have a means to prevent the same load from totaling twice. Once totaled, the load must be
removed from the scale before a new load can be added to the Total. Applied weight must be greater than
the Total Threshold before it can be totaled. See “SETUP TOTAL” for instructions on how to set the Total
Threshold.
To Total with the TOTAL Key
(Unit must be setup to Manual Total mode)
Rules for use:
1) The motion annunciator must be off, the scale must be stable unless motion is disabled in the Setup Total
menu.
2) Only readings above the High Threshold can be accumulated.
3) The scale adds the current reading (relative to the Net zero or Gross zero depending on mode) to the contents
of the accumulate register.
4) After a weighment is totaled, the weight must go below the Total Threshold before another weight can be
added to the total. This assures that a weight on the scale is only added to the total once.
AUTO TOTAL
SETUP Option, see “SETUP TOTAL” to enable Auto Total.
When the weight exceeds the Total Threshold the total function operates automatically.
There are 5 modes of Auto Total. Each mode is used in slightly different ways.
Mode 1, Autonorm: The displayed weight is held in a holding register and added when the weight returns below
the Total Threshold. The last settled reading is what will be used for totaling when the scale returns below the
Total Threshold. The user must make sure that while removing the load the scale does not stabilize enough for
a new reading or an erroneous weighment addition could occur. The last settled weight is actually added to the
total when the scale returns to below the Total Threshold.
Mode 2, Autopeak: The “AUTOPEAK” total mode works the same as Autonorm, except that the highest settled
reading will be used for totaling on return to zero, rather than the last settled reading.
Mode 3, Autoload: totals the applied weight as soon as the weight is stable (Motion Indicator off). Additional
weight cannot be totaled until the weight drops below the Total Threshold
Mode 4, Loaddrop: After pressing the
TOTAL key, the CellScale starts a long term, motion compensated (if the
motion compensation option is installed in the CellScale), average of the current weight that ends when the weight
is dropped. This method is designed for commodity weighing of scrap metal, or other types of materials that are
loaded into rail cars, trucks, hoppers, etc., usually with a crane.
Place the weight to be totaled on the scale. When the weight has stabilized, press the TOTAL Key [F1] .
The current weight is added to the total register. If the display is setup to display the total, the display gives
an indication of how many weighments have been totaled. i.e. 6 #. There may be a small delay before the
CellScale reports back to the 9850 the new Total and Total weighments.
On Autonorm, Autopeak, and Loaddrop modes, the Total is not recorded until the weight is removed
(weight drops below the total threshold). When combining print modes with totals, this can cause the
total to lag by one reading. Use the Autoload or Onaccept modes if an immediate current weight and
totaled weight printout is required.
Mode 5, Onaccept: In conjunction with target weights set up in the set points menus, the Onaccept total mode
will automatically total settled readings that fall within the preselected accept weight window. See Section 8 “Set
Points” for information on setting accept limits.
!
Go to Index