H3C Technologies H3C S12500-X Series Switches User Manual
Layer 2—lan switching configuration guide
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- Title Page
- Preface
- Contents
- Configuring Ethernet interfaces
- Configuring a management Ethernet interface
- Ethernet interface naming conventions
- Configuring common Ethernet interface settings
- Splitting a 40-GE interface and combining split 10-GE interfaces
- Configuring basic settings of an Ethernet interface
- Configuring the link mode of an Ethernet interface
- Configuring jumbo frame support
- Configuring physical state change suppression on an Ethernet interface
- Performing a loopback test on an Ethernet interface
- Configuring generic flow control on an Ethernet interface
- Configuring PFC on an Ethernet interface
- Setting the statistics polling interval
- Forcibly bringing up a fiber port
- Configuring a Layer 2 Ethernet interface
- Displaying and maintaining an Ethernet interface
- Configuring loopback, null, and inloopback interfaces
- Bulk configuring interfaces
- Configuring the MAC address table
- Overview
- Configuring the MAC address table
- Configuring MAC address entries
- Adding or modifying a blackhole MAC address entry
- Adding or modifying a multiport unicast MAC address entry
- Disabling MAC address learning
- Configuring the aging timer for dynamic MAC address entries
- Configuring the MAC learning limit on interfaces
- Configuring the frame forwarding rule
- Assigning MAC learning priority to interfaces
- Enabling MAC address synchronization
- Displaying and maintaining the MAC address table
- MAC address table configuration example
- Configuring MAC Information
- Configuring Ethernet link aggregation
- Basic concepts
- Aggregating links in static mode
- Aggregating links in dynamic mode
- Load sharing criteria for link aggregation groups
- Ethernet link aggregation configuration task list
- Configuring an aggregation group
- Configuring a Layer 2 aggregate interface
- Configuring the description of a Layer 2 aggregate interface
- Specifying ignored VLANs on a Layer 2 aggregate interface
- Setting the minimum and maximum numbers of Selected ports for an aggregation group
- Configuring the expected bandwidth of an aggregate interface
- Shutting down an aggregate interface
- Restoring the default settings for an aggregate interface
- Configuring load sharing for link aggregation groups
- Enabling link-aggregation traffic redirection
- Displaying and maintaining Ethernet link aggregation
- Ethernet link aggregation configuration examples
- Configuring port isolation
- Configuring spanning tree protocols
- STP
- RSTP
- MSTP
- Protocols and standards
- Spanning tree configuration task lists
- Setting the spanning tree mode
- Configuring an MST region
- Configuring the root bridge or a secondary root bridge
- Configuring the device priority
- Configuring the maximum hops of an MST region
- Configuring the network diameter of a switched network
- Configuring spanning tree timers
- Configuring the timeout factor
- Configuring the BPDU transmission rate
- Configuring edge ports
- Configuring path costs of ports
- Configuring the port priority
- Configuring the port link type
- Configuring the mode a port uses to recognize and send MSTP packets
- Enabling outputting port state transition information
- Enabling the spanning tree feature
- Performing mCheck
- Configuring Digest Snooping
- Configuring No Agreement Check
- Configuring protection functions
- Displaying and maintaining the spanning tree
- Spanning tree configuration example
- Configuring loop detection
- Configuring VLANs
- Configuring the private VLAN
- Configuring QinQ
- Configuring VLAN mapping
- Configuring LLDP
- Overview
- LLDP configuration task list
- Performing basic LLDP configuration
- Enabling LLDP
- Configuring the LLDP bridge mode
- Setting the LLDP operating mode
- Setting the LLDP re-initialization delay
- Enabling LLDP polling
- Configuring the advertisable TLVs
- Configuring the management address and its encoding format
- Setting other LLDP parameters
- Setting an encapsulation format for LLDPDUs
- Configuring CDP compatibility
- Configuring DCBX
- Configuring LLDP trapping and LLDP-MED trapping
- Displaying and maintaining LLDP
- LLDP configuration examples
- Configuring service loopback groups