13 industry canada (ic) compliance, Industry canada (ic) compliance -10 – Yokogawa Wireless Temperature Transmitter YTA510 User Manual

Page 18

Advertising
background image

<2. Notes on Handling>

2-10

IM 01C50E01-01EN

Co-located:

This transmitter must not be co-located or

operated in conjunction with any other antenna

or transmitter.

FCC WARNING:

Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

NOTE

This equipment has been tested and found

to comply with the limits for a Class A digital

device, pursuant to part 15 of he FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when

the equipment is operated in a commercial

environment.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction

manual,may cause harmful interference to radio

communications. Operation of this equipment

in a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

2.13 Industry Canada (IC)

compliance

This equipment contains transmitter module IC:

8999A-WIC001.

This Class A digital apparatus complies with

Canadian ICES-003.
This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to

the following two conditions: (1) this device may not

cause interference, and (2) this device must accept

any interference, including interference that may

cause undesired ,operation of the device.
Under Industry Canada regulations, this radio

transmitter may only operate using an antenna of a

type and maximum (or lesser) gain approved for the

transmitter by Industry Canada. To reduce potential

radio interference to other users, the antenna type

and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more

than that necessary for successful communication.

This radio transmitter IC Number 8999A-WIC001

has been approved by Industry Canada to operate

with the antenna types listed below with the

maximum permissible gain and required antenna

impedance for each antenna type indicated.

Antenna types not included in this list, having a gain

greater than the maximum gain indicated for that

type, are strictly prohibited for use with this device.

Antenna type:

Gain:

COLLINEAR

9 dBi, 50 Ω

Sleeve

2.14 dBi, 50 Ω

French:
Cet appareil numérique de la classe A est conforme

à la norme NMB-003 du Canada.
Le présent appareil est conforme aux CNR

d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1)

l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.
Conformément à la réglementation d’Industrie

Canada, le présent émetteur radio peut fonctionner

avec une antenne d’un type et d’un gain maximal

(ou inférieur) approuvé pour l’émetteur par Industrie

Canada. Dans le but de réduire les risques de

brouillage radioélectrique à l’intention des autres

utilisateurs, il faut choisir le type d’antenne et son

gain de sorte que la puissance isotrope rayonnée

équivalente (p.i.r.e.) ne dépasse pas l’intensité

nécessaire à l’établissement d’une communication

satisfaisante.
Le présent émetteur radio IC Number

8999A-WIC001 a été approuvé par Industrie

Canada pour fonctionner avec les types d’antenne

énumérés ci-dessous et ayant un gain admissible

maximal et l’impédance requise pour chaque type

d’antenne. Les types d’antenne non inclus dans

cette liste, ou dont le gain est supérieur au gain

maximal indiqué, sont strictement interdits pour

l’exploitation de l’émetteur.

Antenna type:

Gain:

COLLINEAR

9 dBi, 50 Ω

Sleeve

2.14 dBi, 50 Ω

Advertising