HP XP Continuous Access Software User Manual
Page 173
• VOL: Volume manipulated during the operation. This volume is located in the local array.
The number to the left of the colon (:) is the CU number. The number to the right of the
colon is the LDEV number.
• Paired VOL: Volume paired with the manipulated volume. This volume is located in the remote
array. The number to the left of the colon (:) is the CU number. The number to the right
of the colon is the LDEV number.
• Operation: Operation performed.
• Pair definition: Data volume pair was defined.
• Paircreate Start: Creation of data volume pair was started.
• Paircreate Complete: Creation of data volume pair was finished.
• Pairresync Start: Restoring data volume pair was started.
• Pairresync Complete: Restoring data volume pair was finished.
• Pairsplit-r Start: Splitting (Suspending) data volume pair was started.
• Pairsplit-r Complete: Splitting (Suspending) data volume pair was finished.
• Pairsplit-r(Failure): Data volume pair was split (suspended) because of a failure.
• Pairsplit-S Start: Deleting data volume pair was started.
• Pairsplit-S Complete: Deleting data volume pair was finished.
• Status Change by MCU(SMPL to COPY): Status of data volume pair was changed from
SMPL to COPY because of an operation from the primary array.
• Status Change by MCU(SMPL to PAIR): Status of data volume pair was changed from SMPL
to PAIR because of an operation from the primary array.
• Status Change by MCU(COPY to PAIR): Status of data volume pair was changed from
COPY to PAIR because of an operation from the primary array.
• Status Change by MCU(COPY to PSUS/PSUE): Status of data volume pair was changed
from COPY to PSUS or PSUE because of an operation from the primary array.
• Status Change by MCU(PAIR to PSUS/PSUE): Status of data volume pair was changed from
PAIR to PSUS or PSUE because of an operation from the primary array.
• Status Change by MCU(PAIR to SMPL): Status of data volume pair was changed from PAIR
to SMPL because of an operation from the primary array.
• Status Change by MCU(COPY to SMPL): Status of data volume pair was changed from
COPY to SMPL because of an operation from the primary array.
• Status Change by MCU(PSUS/PSUE to SMPL): Status of data volume pair was changed
from PSUS or PSUE to SMPL because of an operation from the primary array.
• Status Change by MCU(PSUS/PSUE to COPY): Status of data volume pair was changed
from PSUS or PSUE to COPY because of an operation from the primary array.
• Status Change by RCU(Pairsplit-r Start): Status of data volume pair was changed because
an operation for splitting a pair started at the secondary array.
• Status Change by RCU(Pairsplit-r Complete): Status of data volume pair was changed
because an operation for splitting a pair finished at the secondary array.
• Status Change by RCU(PSUS/PSUE to SMPL, Pairsplit-S Start): Operation for deleting
a pair was started at the secondary array. Status of data volume pair changes from
PSUS or PSUE to SMPL.
• Status Change by RCU(COPY to SMPL, Pairsplit-S Start): Operation for deleting a pair was
started at the secondary array. Status of data volume pair changes from COPY to SMPL.
• Status Change by RCU(PAIR to SMPL, Pairsplit-S Start): Operation for deleting a pair was
started at the secondary array. Status of the data volume pair changes from PAIR to SMPL.
• Status Change by RCU(Pairsplit-S Complete): Status of data volume pair was changed
because an operation for deleting a pair finished at the secondary array.
• Unknown: Array could not identify the operation.
Continuous Access XP Journal user guide
173