Document Outline

• 1747-UM005B-EN-P, DH-485/RS-232C Interface Module User Manual
  • Important User Information
• Summary of Changes
  • Notes:
• Table of Contents
• Preface
  • Purpose of This Manual
    • Related Documentation
  • Who Should Use This Manual
    • Terms and Abbreviations
  • Conventions Used in This Manual
• 1 - Overview
  • Overview
  • Interface Module Overview
    • Interface Module Overview
  • Features
    • 1747-KE Module Features
    • LED Indicators
    • LED Indicator Status
    • Jumper Placement
  • Use a Modem with Your Interface Module
  • Use DF1 Protocol and Your Module
    • DF1 Protocol
  • Typical Configurations
    • Full-duplex (Point-to-point)
    • Full-duplex (Network, Example 1)
    • Full-duplex (Network, Example 2)
    • Half-duplex (Local Mode) Master
    • Half-duplex (Remote Mode) Master
    • Half-duplex (Slave-to-slave Communication)
• 2 - Quick Start
  • Quick Start
  • Required Tools and Equipment
  • Procedures
• 3 - Communicate with the Interface Module
  • Communicate with the Interface Module
  • DF1 Communication
    • Full-duplex (Point-to-point)
      • Full-duplex (Point-to-point)
    • Full-duplex (Network Example)
      • Full-duplex (Network Example)
    • Local Mode
      • Local Mode
    • Remote Mode
      • Half-duplex Remote Address Conversion Table
    • Remote Mode Addressing on a Multi-drop Network Example
      • Remote Mode Addressing on a Multi-drop Network
      • Addresses
      • Devices and Corresponding Addresses
    • Slave-to-slave Communication
      • Slave-to-slave Communication
      • Slave-to-slave communication
  • Communicate with DH-485 Devices
  • Communicate with a Modem
• 4 - Installation and System Configuration
  • Installation and System Configuration
  • European Union Directives Compliance
  • Choose the Module’s Functionality
    • Module Functionality Settings
    • Series A Functionality
    • Series B Functionality
  • Set the Module’s Mode
    • JW4 in Configuration Mode
    • JW4 in Vertical Run Mode
  • Verify CONFIG Port Configuration
    • CONFIG Port Configuration
  • Verify DF1 Port Configuration
    • DF1 Port Configuration
  • Install Your Module in an Open Slot
  • Connect Cable to CONFIG or DF1 Ports
    • Pin Assignments for CONFIG and DF1 Ports
    • RS-423/232 DTE to DCE (Non-modem Hardware Handshake to DCE)
    • RS-423/232 DTE to DCE (Modem Hardware Handshake to DCE)
    • RS-423/232 DTE to DCE (No Handshake to DCE)
    • RS-423/232 DTE to DTE (Soft or No Handshake to DTE
    • RS-422
    • RS-485
  • Connect Cable to the DH-485 Port
    • Connect to the DH-485 Port via the 1747-C11 Cable
    • Connect to the DH-485 Port via the 1747-C11 Cable
    • Connect to the DH-485 Port via the 1747-C13 Cable
  • Configure Your SLC Chassis
  • Configure the DF1 Driver within RSLinx Software
  • Configure Your Module
  • Complete the Installation of Your Module
    • a. Remove the module from the chassis.
    • b. Place your module in Run mode using JW4
    • c. Re-insert the module into the chassis.
• 5 - Module Configuration with a Terminal Overview
  • Module Configuration Using an ASCII Terminal
  • ASCII Terminal Configuration
    • ASCII Terminal Configuration
  • Module Configuration with a Terminal Overview
    • Menu Structure
  • Top Level Setup Menu
    • Top Level Setup Menu
  • CONFIG Port Menu
    • CONFIG Port Setup Menu
    • CONFIG PORT Setup Parameters
  • DF1 Port Menu
    • DF1 PORT Setup Menu
    • DF1 Port Setup Parameters
  • DH-485 Port Menu
    • DH-485 Port Menu
    • DH-485 Port Setup Parameters
  • DF1 Protocol Menu
    • DF1 Protocol Menu
    • DF1 Full-duplex Setup Menu
    • DF1 Full-duplex Setup Parameters
    • DF1 Half-duplex Setup Menu
    • DF1 Half-duplex Setup Parameters
  • Display Parameters Menu
    • Full-duplex Setup Summary
    • Half-duplex Setup Summary
• 6 - Module Configuration Using the Backplane
  • Module Configuration Using the Backplane
  • Overview
    • Valid Data ID Values
  • Configure the Interface Module from the SLC Processor
    • Configure the Module From the SLC Processor
  • Place the Module into Software Run Mode from SLC Processor
    • Place the Module in Run Mode
  • Read the Module’s Configuration from the SLC Processor
    • Read the Module’s Configuration from the SLC Processor
  • Examine the SLC Processor’s Status Word
    • SLC Output Status Word Status Bits
    • SLC Input Status Word Status Bits
    • Status Codes from the Module to the SLC Processor
  • Build the DF1 Configuration Packet
    • SLC Output File to the Interface Module
    • DF1 Port Setup Parameters
    • DF1 Full-duplex Setup Parameters
    • DF1 Half-duplex Setup Parameters
  • Build the DH-485 Configuration Packet
    • SLC Output File to the Interface Module
    • DH-485 Port Setup Parameters
  • Build the Modem Init String Configuration Packets
    • SLC Output File to the Interface Module
    • SLC Output File to the Interface Module
  • Use the Real Time Clock
    • SLC Output Status to the Interface Module
  • Establish a Data Echo Between the Interface Module and the SLC Processor
    • Establish a Data Echo
    • SLC Output File to the Interface Module
  • Reset the Interface Module from the SLC Processor
    • Reset the Module from the SLC Processor
• 7 - Interpret the LED Indicators
  • Interpret the LED Indicators
  • Interface Module Status Indicators
    • LED Indicators
    • LED Indicator Error Conditions
  • Input Image Description
    • Input Image
  • Status Codes from the Module to the Processor
    • Status Codes from the Module to the SLC Processor
  • SLC Fault Code
    • SLC Fault Codes
• 8 - Application Examples
  • Application Examples
  • Basic Configuration Example Using the Backplane
    • Parameter Locations
    • DF1 Configuration (N10:11...17)
    • DH-485 Configuration (N10:21...27)
    • Modem Init String Characters 1-14 (N10:31-37)
    • Modem Init String Characters 15-28 (N10:41-47)
      • Failed Configuration Block
      • Configuration Data Table
  • Supplementary Example Using the Backplane
    • Parameter Settings
    • User Program
    • Configuration Data Table
      • Configuration Data Table
    • User Program
    • Configuration Data Table
      • Configuration Data Table
  • RSLogix Software to SLC Network via Modem Example
    • RSLogix Software to SLC Network
    • Modify an Existing Driver
    • Add a New Driver
    • Configure the driver for KE Communication through a Modem
    • Modem Dialer Configuration Dialog
• A - Specifications
  • Specifications
  • Hardware Specifications
    • Hardware Specifications
    • Product Certifications
    • Port Isolation
    • Maximum Communication Distances
• B - PLC-5 to SLC 500 Communications
  • PLC-5 to SLC 500 Communications
  • Overview
  • PLC-5 Message Instruction
  • Use the SLC 500 CIF File
    • SLC 500 CIF File
  • Use the PLC-5 Message Instruction with Word
  • Use the PLC-5 Message Instruction with Byte
    • Destination Address
• C - Lithium Battery Replacement, Handling, and Disposal
  • Lithium Battery Replacement, Handling, and Disposal
  • Battery Replacement
    • Battery Location
  • Battery Handling
    • One or Two Batteries
    • Three or More Batteries
  • Battery Disposal
• D - Interface Module Configuration Worksheets
  • Interface Module Configuration Worksheets
  • DF1 Full-duplex
    • DH485 Port
    • DF1 Port
    • DF1 Full-duplex
  • DF1 Half-duplex
    • DH485 Port
    • DF1 Port
    • DF1 Half-duplex
  • Index
  • Numerics
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • J
  • L
  • M
  • N
  • O
  • P
  • Q
  • R
  • S
  • T
  • W
• Index
• Back Cover